How to Change Cabin Air Filter and Engine Air Filter for 2020 Subaru Outback

Here are pic­tures doc­u­ment­ing the change/replacement of the cab­in and engine air fil­ters of my 2020 Sub­aru Out­back Onyx XT.

Project dura­tion: 10 min­utes under good con­di­tions

Tools need­ed: Hands, maybe a flash­light.

Cab­in Air Fil­ter

Open your glove com­part­ment.

There’s a tab on the right hand side when you open it. Just tug on it high­er up and it comes right off.

On either side of the glove box, are hinges as shown in the upper pic­ture. Push hard on either side to pop them out. It might be hard to do if your car is new­er or when it’s cold. Mine qual­i­fied under both con­di­tions and I had a heck of a time.

Aaaand, it final­ly came out!

Here’s a close­up of one of those hinges. Sub­aru gave it extra felt. Kin­da nice.

And here you have the cab­in air fil­ter box.

I could­n’t fig­ure out how to remove this piece and man­aged to break off one of the clasps on the side of the cab­in air fil­ter box like an idiot. 🙁 All you have to do is squeeze those two things on the bot­tom at the same time and it comes right off.

Here’s the old one.

I don’t think the fil­ter has been changed since I first bought the car Nov of 2019, so it’s been over a year (it is mid-Feb 2021 right now). That’s a gen­uine Sub­aru cab­in air fil­ter.

This is the new fil­ter installed. **N.B. From var­i­ous online videos, I hear that Sub­aru’s air flow is from top to down, but Sub­aru is appar­ent­ly one of the few (if not the only) car man­u­fac­tur­ers for which the OEM cab­in air fil­ter arrow does­n’t cor­re­spond with air flow direc­tion. If you’re using after­mar­ket, then make sure you fol­low the air flow.**

OK, then you just put it back togeth­er. Cov­er on the fil­ter box, line up the bot­tom hinges of the glove box and sim­ply push up until it snaps in, then make sure you replace the lit­tle clasp on the right side and BOOM, you’re done!

Engine Air Fil­ter

Open the hood

On the left side of the engine bay, find this and unhook the met­al clasps.

If you wig­gle it apart, you’ll see the old engine air fil­ter.

Just pull it out.

I used a gen­uine Sub­aru engine air fil­ter. The new one is on the left and the old one on the right.

You just slide it in there, foam-side fac­ing the back of the car, close up the clasps, and you’re done!

Yay!

DIY: Replacing 2012 Subaru Outback Brake Light Bulb

03/22/2018

One of my brake lights went out, so I need­ed to replace it.

Dif­fi­cul­ty: Very Easy!

Time: 5–10 min­utes

Tools: Philips head screwdriver(s), replace­ment bulb, gloves (impor­tant!!) and option­al ratch­et­ing sock­et wrench

Here we go!

  1. Open the trunk and you see this:
20180322_191101480817628.jpg

2. Use the screw­driv­er to unscrew, and you’ll feel it click twice-ish

20180322_191036599386176.jpg

3. It’ll pop out like this, so care­ful­ly twist/pull it and the ring out. Repeat with the 2nd one

20180322_1910291470127601.jpg

4. Care­ful­ly insert a thin screw­driv­er or pry tool around the side clos­est to the out­side and gen­tly loosen the part until it pops out

20180322_1910021985675847.jpg

5. Now you see this

20180322_190617683472556.jpg

6. Take your big­ger screw dri­ver and locate these screws. Mine hap­pened to be stripped from last time and replaced WAY too tight­ly, so I need­ed the sock­et wrench to help

20180322_190620890298486.jpg
20180322_1906511234044080.jpg

8. And with a lit­tle pull towards you, the whole hous­ing comes off!

9. The one we need today is the mid­dle grey one where the lines con­nect. Just a lit­tle twist and off it comes

10. There’s the old bulb. Just give it a tug and replace it with the new bulb

20180322_190808206905897.jpg

11. New bulb! *Impor­tant* Wear gloves before putting the new bulb in!! So, every­thing now goes back­wards. Put the bulb in and twist until it locks in place

12. Replace the brake hous­ing. There are two tabs on the side where the hous­ing will slide into.

20180322_1908541715738830.jpg

13. Slide it in…and…

14. …push! It’ll click into place.

15. Do every­thing back­wards and VOILA!!!

All done. Make sure the light works, but that’s all there is to it!!!

This is what hap­pens, by the way, when you touch the bulbs with your bare hands. The upper bulb has a burned spot where the oil from my fin­ger got, heat­ed up, and *poof* burned out the bulb.