Ford Maverick DIY FlexBed’s Projects

updat­ed 2/12/2022

This is just a writ­ten-out ver­sion of the DIY instruc­tions by Ford found in their videos HERE. My expe­ri­ence with attempt­ing some of the projects are HERE.

Bed Divider

  • Cut wood to size and place into built-in slots to cre­ate dividers
    • Rear Board (near tail­gate): 54in
    • Front Board (near cab): 43–1/4in

Bed Side Rails

  • Mate­ri­als Need­ed:
    • Two - 30in, 12-gauge, half slot­ted met­al fram­ing strut chan­nels
    • Four - 12-gauge, blue, strut end caps for B‑series chan­nel
    • Four - 3⁄8″ x 11⁄16″ machin­ery eye bolts
    • Four - 3/8in nylon strut cone nuts
    • Four - 3⁄8″ x 1–1/2″ fend­er wash­ers
    • Six - M6 — 1.0 x 25mm inter­nal hex, but­ton-head cap screw (See note below)
    • Six - 1–1/4″ Fend­er wash­ers* (see step 2‑C)
    • Met­al File
  • Ford’s How-To Video: HERE
    • Make sure to use safe­ty gear (glass­es, gloves, etc)
    • Step 1 — Smooth the Edges
      • After cut­ting the met­al struts into 30in pieces, smooth down the edges with a met­al file
    • Step 2 - Insert Cone Nuts
      • Insert 2 nylon cone nuts into each rail (will be used to attach eye bolts lat­er)
      • Align the rail with the cen­ter of the bed
      • Attach rail to bed with the M6 bolts and 1–1/4″ fend­er wash­ers
        • N.B. The video nev­er men­tioned these 1–1/4″ fend­er wash­ers in the mate­ri­als list, and then it appeared in this step
    • Step 3 — Attach Eye Bolts to Spring Nuts
      • Slide the nylon cone nuts to desired loca­tion for the eye bolts
      • Place 1–1/2″ fend­er wash­ers on each eye bolt and screw into strut cone nuts
      • Add end caps to rails
    • Done!
    • Note: The linked video calls for M6 screws, but the pre-drilled side holes in my Mav­er­ick are larg­er than M6’s. The orig­i­nal video from Ford calls for “a mix of M6 and M8 screws.” At this point in time I have yet to get my hands on M8 screws, so I don’t know for sure yet.

Bike Rack

  • Mate­ri­als Need­ed:
    • One - 2″ x 6″ Wood Board approx­i­mate­ly 43.25in long
    • Two - Bike Fork Mounts (that fit your bike)
    • Six - #10 x 1–3/4″ Wood Screws
    • Four - Ratch­et Tie Down Straps
  • Ford’s How-To Video: HERE
    • Step 1 — Posi­tion the Board
      • Insert board at wheel­house area (near the cab)
      • Smooth edges with sand­pa­per if need­ed
      • Fit should be snug but not dif­fi­cult
    • Step 2 — Attach Fork Mounts
      • Mea­sure 14–3/8″ from either side of the board
      • Mark the cen­ter (3 inch­es) of each mea­sure­ment
      • Align the fork mounts cen­tered on the marks
      • Mark hole posi­tions
      • Drill pilot holes with a 13⁄64″ drill bit
      • Align mounts over the holes
      • Dri­ve screws in
      • Insert board with attached mounts into bed
    • Step 3 — Attach Your Bike
      • Remove front wheels and attach to fork mounts
      • Secure the mount fas­ten­ers
      • Use ratch­et tie downs to secure the seat tube to the anchors on truck bed sides
      • Pass straps of anoth­er tie-down across the top tubes and attach it at both sides
    • Step 4 — Secure Tires
      • Posi­tion wheels between the board and truck bed (against the cab)
      • Use adjustable strap to loop the wheel, wood board, and floor anchor togeth­er
      • Make sure all straps are secured tight­ly
    • Done!

Bed Rail Light­ing

  • Mate­ri­als Need­ed:
    • Two - IP86 Rat­ed Water­proof Light­ing Strips
    • Sol­der­ing gun
    • Roll of Elec­tri­cal Tape
    • Pack­age Elec­tri­cal Shrinkwrap
    • One - IP86 rat­ed Water­proof Switch** (see N.B. at end of sec­tion)
    • Pair of Wire Strip­pers
    • Push-Pin Cable Ties
    • Scrap Wire
    • Heat Gun
  • Ford’s How-To Video: HERE
    • Safe­ty Check!
      • Dis­con­nect Bat­tery
      • Nev­er illu­mi­nate while dri­ving
      • Make sure lights do not project above the rails
    • Step 1 — Find the Wire
      • Find wire (make sure bat­tery is dis­con­nect­ed!)
      • Remove the 12‑V access cov­er on D‑Pillar and pull the wiring har­ness from the hold­er
      • Unwind tape con­nect­ing the wire
    • Step 2 — Thread the Wire
      • Thread wire from top of pil­lar down to the har­ness
      • Use elec­tri­cal tape to secure the end of the wire to the match­ing con­nec­tor pig­tail pro­vid­ed with your truck
      • Pull wire from the top so you have suf­fi­cient length of the pig­tail to sol­der to your acces­so­ry
    • Step 3 — Heat the Wire
      • Stripe wires from acces­sories
      • Slide on shrinkwrap before mak­ing the joint
      • Sol­der red to red, and black to black
      • Slide shrinkwrap onto the joint
      • Heat shrinkwrap with heat gun until tight on the joint
      • Push con­nec­tor plate back inside the D‑pillar
    • Step 4 — Attach­ing to the Bed
      • Use cable ties to attach the light­ing so they shine towards the adja­cent bed­side
      • Cut light­ing to length, peel off back­ing to attach to bed, tight­en and trim cable ties
      • Deter­mine desired loca­tion of switch and secure
    • Re-con­nect bat­tery
    • Done!
    • N.B. It is nev­er clar­i­fied in the video, but I assume that you have to repeat on one side what you did on the oth­er? Do you run the strips along the far back of the bed to the oth­er side to con­nect them? The video shows cut­ting the light strip to fit one side. Or maybe have 2 switch­es, one for either side if you want 2?

Merge Mansion — 2021 Christmas Event Item List Guide

Updat­ed 01/01/2022

An Un-Offi­cial Item List Cas­cade Guide by a Merge Man­sion Fan for the Christ­mas Event

**Dis­claimer: All assets and rights belong to Meta­core Games**

Main Merge Man­sion Item Guide (click me!)

Merg­ing Cas­cades (A‑Z)

Can­dle

  • From: Old Enve­lope, Event Store
  • Items Obtained: Sock, Gift Box­es (lvls 1–3), Old Enve­lope (50% chance once emp­ty)
  • Cas­cade: Can­dle lvl1 > Can­dle lvl 2 > Can­dle lvl 3 > Can­dle lvl 4 (max)
  • Note: Halves the time for melt­ing Snow­man when placed near

Chim­ney

  • From: Event Start
  • Items Obtained: Gift Bag, Coal,
  • Cas­cade: Brick > Pile of Bricks > Chim­ney (max)
  • Note: Not sure why the game did­n’t pick up the Brick image. It’s avail­able at Event Start

Coal

  • From: Chim­ney, Event Store
  • Cas­cade: Piece of Coal > Pile of Coals > Bag of Coals (max)
  • Use: Feed to Grand­ma’s Oven

Gift Bag

  • From: Chim­ney
  • Items Obtained: Gift Box­es (lvls 1–3), Old Enve­lope, Twig (low chance)

Gift Box­es

  • From: Gift Bag
  • Items Obtained: Hol­i­day Tie, Toy Giraffe, Rock­ing Horse, Toy Drum
  • Cas­cade: Cou­ple Gifts > Mul­ti­ple Gifts > So Many Gifts
  • Note: Gift Box­es can­not be merged and are obtained sep­a­rate­ly

Greens

  • From: Xmas Tree lvl 4+
  • Items Obtained: Bell (from Crown)
  • Cas­cade: Cone > Trim­ming > Mistle­toe > Gar­land > Wreath > Crown (max)
  • Note: Once Bell is received, it Crown to Wreath (lvl 5) and will need to be merged again

Grand­ma’s Oven

  • From: Event Start
  • Items Obtained: Cook­ie

Hol­i­day Clothes

  • From: Gift Box­es
  • Cas­cade: Hol­i­day Tie > Wool Socks > San­ta Beanie > Win­ter Scarf > Felt Slip­pers > Hol­i­day Pullover > Warm Gloves > Win­ter Sweater > Ready for the North (max)

Hol­i­day Treats

  • From: Full Sock
  • Cas­cade: Sweet > Choco­late > Caramel > Can­dy Cane > Eggnog (max)
  • Use: feed Caramel to Grand­ma’s Oven

Love­ly Cook­ies

  • From: Grand­ma’s Oven
  • Cas­cade: Cook­ie lvl 1 > Cook­ie lvl 2 > Cook­ie lvl 3 > Cook­ie lvl 4 > Cook­ie lvl 5 > Cook­ie lvl 6 > Cook­ie lvl 7 (max)

Old Enve­lope

  • From: Gift Bag (50% chance)
  • Items Obtained: Can­dle, Post­cards

Post­cards

  • From: Old Enve­lope
  • Cas­cade: Hon­ey > Mr. Boul­ton > Dear Ursala > Mrs. Boul­ton > Dear Res­i­dent > Con­fi­den­tial > Invi­ta­tion (max)
  • Notes: See bot­tom of page for Post­card Text

Pud­dle

  • From: Snow­man (melt­ed)
  • Items Obtained: Twig (x2), Scarf

Snow­man

  • From: Win­ter Globe
  • Items Obtained: Pud­dle
  • Cas­cade: Snowflake > Snow­ball > Snow­ball Pile > Cold Feet > Snow­man (max)
  • Note: Place near Can­dle (lvl 4) to halve melt­ing time

Socks

  • From: Chim­ney, Event Store
  • Items Obtained: Sweet, Choco­late, Toy Robot
  • Cas­cade: Emp­ty Sock > Half-filled Sock > Full Sock (max)

Toy Robot

  • From: Socks (low chance), Event Store

Toys

  • From: Gift Box­es
  • Items Obtained: Snowflake (from Win­ter Globe)
  • Cas­cade: Toy Giraffe > Rock­ing Horse > Toy Drum > Toy Sol­dier > Ted­dy Bear > Spin­ning Top > Toy Loco­mo­tive > Win­ter Globe (max)

Xmas Tree

  • From: Event Start, Pud­dle, Gift Bag (low chance)
  • Items Obtained: Cone (from lvl 4)
  • Cas­cade: Twig > Sapling > Young Ever­green > Full-grown Ever­green > Christ­mas Tree > Cute Christ­mas Tree > Classy Christ­mas Tree > Gor­geous Christ­mas Tree > Fab­u­lous Christ­mas Tree (max)
  • Note: Feed lvl 5+ Xmas Tree Dec­o­ra­tions to progress. Only lvl 4 pro­duces Cone

Xmas Tree Dec­o­ra­tions

  • From: Crown (Greens), Event Store
  • Cas­cade: Bell > Ball > Two Balls > Tree­top (max)

Post­cards Text

  1. Hon­ey (lvl 1) - Hap­py Hol­i­days! Hope every­thing is get­ting bet­ter at the Man­sion. Don’t wor­ry, I’ll be back soon­er than you think. Yours, U
  2. Mr. Boul­ton (lvl2) — Your lat­est pay­ment was due last week. We can wait over the hol­i­days but no longer than that
  3. Dear Ursala (lvl 3) - Win­ter is so cold with­out you. Do what you have to, but please come back soon! Love, C
  4. Mrs. Boul­ton (lvl 4) — We haven’t reached your hus­band despite our notable efforts. Here are all his unpaid bills. Could you please give us a call?
  5. Dear Res­i­dent (lvl 5) — Thank you for pay­ing all the bills. It was done from an anony­mous account but that is prob­a­bly just some tech­ni­cal error.
  6. Con­fi­den­tial (lvl 6) — You can pay back with a lit­tle favor. Find the plan in the enve­lope. This year’s hol­i­day cel­e­bra­tion will be a sur­pris­ing one…
  7. Invi­ta­tion (lvl 7) - Hol­i­day Ball 1979 is com­ing! Get your cos­tumes ready. This will be an unfor­get­table night at the Man­sion… — Boul­tons

Tips and Tricks

  • Items to focus on gath­er­ing:
    • Win­ter Globe –> Snow­man –> Twig
    • Cones –> Bell
  • Try to keep mul­ti­ple Xmas Tree lvl 4 (Full-Grown Ever­green) around for Cone pro­duc­tion