DIY: Toilet Fill Valve Seal Repair

updat­ed 8/7/2022

What: Kohler High­line Clas­sic K‑11499–0 (bought and installed May 2017) toi­let fill valve (Flu­id­mas­ter Uni­ver­sal 400A OE part — came with toi­let) issues

Prob­lem: Months of slow-fill­ing toi­let along with a loud squeal noise when float rais­es with water lev­el. It final­ly quit fill­ing alto­geth­er.

When: August 2022

Sup­plies: 242 Toi­let Replace­ment Seal, a cup

Cost: Around $4 and gas

Time: 10 min­utes

Dif­fi­cul­ty: Easy

Process

1. Turn off the water sup­ply (bath­room got a nice clean­ing after this)

2. Grab the fill valve cap and twist left to unseat it (you might have to grab the stem of the whole valve to pre­vent the entire valve from spin­ning. Here’s a video)

3. Now to unhook the cap from the float. Give it a nice, care­ful tug, being aware that it is plas­tic.

4. Exam­ine the fill valve seal for debris. Remove it care­ful­ly and inspect under­neath for debris. Clean it out. In my case, there was debris under­neath that was caus­ing a block­age and there­fore no water. It must have been there for a while and then final­ly occlud­ed the open­ing.

5. Sim­i­lar­ly, inspect the cap-less top of the fill valve for debris.

Looks clear to me! But just in case…

6. Now that every­thing is off, let’s go ahead and flush the fill valve itself. Appar­ent­ly, over the years pieces of Teflon tape, or min­er­als or oth­er debris can accu­mu­late in the valve. Flu­id­mas­ter sets the lifes­pan of a fill valve at around 7 years (mine is about 5 years old). SO, grab a cup and place it upside-down over the fill valve.

7. Turn on the water sup­ply and flush for about 10–15 sec­onds (accord­ing to Flu­id­mas­ter)

8. At this point, you would replace every­thing and test it out. It was no longer fill­ing slow­ly after the debris was removed, so BOOM, solved. BUT…the float mech­a­nism no longer worked…as in, the fill valve kept fill­ing with­out stop­ping. Oh, great. I bust­ed it some­how. Removed every­thing again and found that the orig­i­nal seal looked kind of chewed up around the float pin.

9. Turned the water sup­ply back off, and ran out to the store to grab a 242 Toi­let Fill Valve Seal (and oth­er stuff just in case, so I would­n’t have to run out again, but did­n’t need them in the end)

10. Had remove it all again and here is an image of the old seal. If you look at the cen­ter, you can see how rough it looks where I tried to push it in with my fin­ger­nails and prob­a­bly from gen­er­al wear and tear

11. Here’s a side by side of the old seal and the new one

12. Slide the seal onto the cap

13. Now to reassem­ble it all. Line up the cap assem­bly with the float assem­bly stem groove and snap it in

*snap*

14. Place the now-attached cap back on the valve. Remem­ber that you have to turn right to replace it, so place the cap accord­ing­ly so that none of the parts inter­fere with each oth­er

*Let’s twist again! Like we did last sum­mer!*

15. Twist it to the right and, YAY, it’s back on!

Reassem­bled!

16. MOMENT OF TRUTH. Turn on the water sup­ply. You should imme­di­ate­ly hear the water fill­ing up. Now lift up on the float mech­a­nism. If the tank quits fill­ing, you are DONE, and it is REPAIRED! GREAT JOB!

Lift up on the float and BOOM! Hal­lelu­jah!

DIY: Replacing 2012 Subaru Outback Brake Light Bulb

03/22/2018

One of my brake lights went out, so I need­ed to replace it.

Dif­fi­cul­ty: Very Easy!

Time: 5–10 min­utes

Tools: Philips head screwdriver(s), replace­ment bulb, gloves (impor­tant!!) and option­al ratch­et­ing sock­et wrench

Here we go!

  1. Open the trunk and you see this:
20180322_191101480817628.jpg

2. Use the screw­driv­er to unscrew, and you’ll feel it click twice-ish

20180322_191036599386176.jpg

3. It’ll pop out like this, so care­ful­ly twist/pull it and the ring out. Repeat with the 2nd one

20180322_1910291470127601.jpg

4. Care­ful­ly insert a thin screw­driv­er or pry tool around the side clos­est to the out­side and gen­tly loosen the part until it pops out

20180322_1910021985675847.jpg

5. Now you see this

20180322_190617683472556.jpg

6. Take your big­ger screw dri­ver and locate these screws. Mine hap­pened to be stripped from last time and replaced WAY too tight­ly, so I need­ed the sock­et wrench to help

20180322_190620890298486.jpg
20180322_1906511234044080.jpg

8. And with a lit­tle pull towards you, the whole hous­ing comes off!

9. The one we need today is the mid­dle grey one where the lines con­nect. Just a lit­tle twist and off it comes

10. There’s the old bulb. Just give it a tug and replace it with the new bulb

20180322_190808206905897.jpg

11. New bulb! *Impor­tant* Wear gloves before putting the new bulb in!! So, every­thing now goes back­wards. Put the bulb in and twist until it locks in place

12. Replace the brake hous­ing. There are two tabs on the side where the hous­ing will slide into.

20180322_1908541715738830.jpg

13. Slide it in…and…

14. …push! It’ll click into place.

15. Do every­thing back­wards and VOILA!!!

All done. Make sure the light works, but that’s all there is to it!!!

This is what hap­pens, by the way, when you touch the bulbs with your bare hands. The upper bulb has a burned spot where the oil from my fin­ger got, heat­ed up, and *poof* burned out the bulb.