I mentioned before that I bought the cheapest option truck because I care mostly about the hybrid and the ability to DIY stuff. Well. The sound system is definitely cheap. TOO cheap, in fact. It sounds absolutely terrible and I got tired of it, so I decided to buy new ones.
Now, this is neither a guide nor gallery of process photos like I normally do, because I did not install it. There are plenty of videos on YouTube to view if you are curious.
All I can say is, WOW, it sounds so much better, so if you are on the fence about upgrading your speakers for your Maverick, do it!
These are factory speakers. They cost $27 from FordApparently small magnets mean cheap in speakers and this is SMALL.
For those of us who don’t want to deal with amps and soldering, etc, for this car, just do the front door speakers. My base XL came with 6 speakers: 2 tweeters in the dash near the windshield, 2 car door speakers, and then 2 basically tweeters in the pillars in the back. The tweeters are very small in the front and hard to work with, and worse for the back, so I opted to leave them alone and just get 2‑way speakers for the door.
This is what the inside of the door looks likeThis is the backside of the door trim
I ended up going to Best Buy after poking around online, so that I could hear the different audio systems that they had. Ultimately, I chose the Alpine S‑S65 2‑way 6–1/2″ speakers.
Bought two 24″ L‑tracks from US Cargo Control along with four L‑track single stud fittings to go with it. There are other sizes, I just opted for the two-footers
The Maverick’s pre-drilled screw holes are threaded and require M8 screws
2ft L‑track with stud fittingsHoles do not line up…Sigh… At least they look good
Unfortunately, the pre-drilled holes on the Maverick and L‑tracks do not line up, so I initially planned to drill 2 extra countersunk holes in the L‑tracks to make it fit. The tracks system really does look nice AND are quite light. According to the site details, they weigh together 1.2lbs.
Next issue: the Maverick has M8 holes, the tracks use 1⁄4″ countersunk hardware (though I found M6 screws fit better than the 1⁄4″). So now some holes need widening
**Below is the original post I made using a drill to try and widen the holes in order to accept the M8 screws. It is lengthy and time consuming and ugly, honestly. Read on if you like, but ten months after the fact, I found out that all you need is a M8 thread tap and t‑handle tapping wrench. Prepping to tap the threads for the floor anchors (click me!), I tested it on these bedside rails, and wow. In what took me originally a few hours, took maybe 2 minutes. Plus, it’s MUCH nicer looking.
FitsStill juts out, but if you got creative, you could probably make it more flushIf I were to do it again, I’d try the deburr tool to see if I could widen the countersink flangeMuch cleaner
You might be able to use a chamfer or a deburring tool to try and set the screw flush, but I don’t have those tools yet. Thanks for reading! The L‑tracks are still super awesome, and great quality looking at them even now. I was able to use them once and they were solid solid solid. However, Ford now offers a Cleat Tie Down Kit for $400 if you want something official**
Original post start
M8 — no fit1⁄4″M6 — the most flushCutting fluid, eye protection, clamps, drill, bits, scrap woodCountersink bit
After having fun using power tools to expand the holes, I realized that the countersink bit I had was too small. Huh.
Be generous with lubeDrillingCountersinkLooks good!Doesn’t fit all the way. Bit too small.
After test-fitting it in the truck bed, I returned to happily make holes. This part was fun, and it was awesome to have success making the hole until…
Drilling hole in metal: SUCCESS!Uh oh. The opening is too smallM8 head is 5/8in or 15.87mm.Opening on the non-circle part is only 10mm. No bit nor rasp could help me
...major problem reached. Because the holes needed to be in the wrong part of the track, there was no way to get the countersink bit in. That’s not that big of a deal, but the screw not fitting in there at all is a huge deal.
Nothing worked.
So, Plan B it is. Went back to the truck bed for further scrutiny, then planned to enlarge 2 of the holes since they were both just off by maybe half a centimeter. Easier said than done. Still the issue with too small of a counter sink. This project was becoming a total experimental project. Those beautiful L‑tracks were looking quite…worked on.
Widening (5/16 bit is very close to M8 size)Screws don’t sit flush. Oh well.Unused mistake holes. ugh.
Plan C was going to be M8 sized eyelet screws. In fact, I might still do that given that there is one screw hole on either side of the bed with nothing it.
Single M8 hole left on either side
Lots of time, teeth clenching, lubricant, and metal shavings later, I was satisfied and went to install them.
YAY!! The screws are absolutely not flush, but I decided that I actually rather like it since I didn’t spring for rail end caps and the screw heads act a bit like stops for the stud fittings.
Screw holds the stud in placeEasy to move spring loaded studJust push and move
Ignoring the weird drilled out holes, it looks pretty good! Just have to make sure not to hook anything to the ends and focus any force near the screw holds.
Pretty proud of myself and definitely learned new things today. Like to not brush at metal shavings with your bare hands because little pieces of metal in your finger is painful.