updatÂed 11/13/2022
N.B. I am a DIYÂer with no autoÂmoÂtive experÂtise
- Cost: $669 + tax
- DifÂfiÂculÂty: Easy
- MateÂriÂals: FendÂer Flares, InstrucÂtion Sheet, 16 retainÂer clips, AutoÂmoÂtive Trim Removal Tools/Retainer Clip Removal Tool (or a screwÂdrivÂer, but much easÂiÂer with the tools), rubÂbing alcoÂhol, paper towÂel, polyurethane sealant, scissors/knife, tape, stool (optionÂal)

ShipÂping





InstalÂlaÂtion
InstrucÂtion sheet and fendÂer flare

Wipe the install locaÂtion with alcoÂhol, then remove the 5 retainÂer clips (3 on the door side and 2 on the front end makÂing sure there are 3 in between).
NOTE: The lowÂest clip on the door-side is a short clip as comÂpared to the longer clips all the othÂers have. This makes re-instalÂlaÂtion imposÂsiÂble, so while youâre not supÂposed to remove the 3 towards the front of the MavÂerÂick, I swapped the midÂdle clip with the short one which fits perÂfectÂly.


To dry fit and mark the alignÂment points, you place, and reseÂcure 3 of the retainÂer clips (donât have to push them in all the way).


InstrucÂtions called for a grease pen to mark the alignÂment, but I used painterâs tape as a guide. Less cleanup.

Remove the clips and the fendÂer flare, then per the instrucÂtions, cut the 3M tape in the midÂdle and tape them off. HonÂestÂly, before I realÂized I could use a plasÂtic pry tool to help, this was the longest, most frusÂtratÂing part of the instalÂlaÂtion. Itâs imposÂsiÂble to get the edges peeled up withÂout nails! The pry tool made it a cinch.
NOTE: As Iâll post a picÂture a litÂtle furÂther down, just peel most of 3M linÂer at the botÂtom part of the flare (closÂest to the wheel). OthÂerÂwise, itâs realÂly hard to pull it off latÂer.


Polyurethane sealant. I used AutoÂmoÂtive AmazÂing Goop because I hapÂpened to have it on hand. The litÂtle nozÂzle I bought for it is super-duper helpÂful. Use your sealant in the built-in chanÂnel


Here we go! Same as before, place the flare on, line it up, secure it with the 3 clips. Now with presÂsure as you go, pull the red 3M linÂer off.


As menÂtioned above, the lowÂest 3M linÂer got stuck underÂneath and was difÂfiÂcult to remove, so just pull most it off before placÂing the flare. Makes it much easÂiÂer.

Yay! Here are the 2 front sides! After doing the first, the 2nd is very easy.


MidÂway point!

AAAAND here is where I hit a snag. As it turns out, the rear retainÂer clips are ALL the small/short clips. And there are 7 on either side that need to be used. I tried, but they are way too short to be able to hold the rear flares in place. Thanks, Ford, for that heads up! So, I have ordered what I think is the equivÂaÂlent of the OE clips and then a set of generÂic clips just in case.
The installed flares look good, though. đ
CONTINUED!
The retainÂer clips from AmaÂzon arrived and, wow! I canât even tell them apart!


Alrighty, then, letâs get installing! Removed the 7 stubÂby clips from the rear. Hereâs an image for size comÂparÂiÂson. I said earÂliÂer that the most time-conÂsumÂing part of this install was peelÂing the 3M linerâŚit is not. The most time-conÂsumÂing part is tryÂing to remove these stubÂby clips. They spin all around the place and itâs more difÂfiÂcult than the longer clips to get a good hold. You get into the groove after a time, though.


DurÂing the dry-fit, new, longer retainÂer clips work perÂfectÂly!


Peel, then secure!


Installed! Looks like Iâm going to need to go back and apply trim restore againâŚthe fendÂer flares are clearÂly newÂer

Repeat on the othÂer side! NowâŚI will add a warnÂing here, because after doing 3 of them I was getÂting a bit cocky. For the very last flare, I decidÂed NOT to do a dry-fit/alignÂment tape. Donât do that. It endÂed up fitÂting just off-kelÂter to where the retainÂing clips wouldÂnât even go all the way in, but the adheÂsive had already stuck and there was no going back.
Itâs done! Hereâs a before and after install picÂture of the last flare.


ComÂpleÂto!! Itâs amazÂing how much difÂferÂent the MavÂerÂick looks with the fendÂer flares on! I honÂestÂly canât realÂly rememÂber what it looked like before!

Notes
- They look realÂly good. RealÂly.
- InstalÂlaÂtion was an overÂall breeze after I proÂcured the propÂer parts. As you can see in my picÂtures, I do not have a driÂveÂway, but nevÂer had to move my car out of the parkÂing space to install these.
- After a week of driÂving, the flares give noticeÂably more drag and thereÂfore reduce the gas effiÂcienÂcy. That part Iâm not as big a fan of, espeÂcialÂly since mine is a hybrid. Then I startÂed wonÂderÂing if the cab spoilÂer would help the aeroÂdyÂnamÂics at all or is simÂply anothÂer cosÂmetÂic thing? The interÂnet is not yieldÂing any real inforÂmaÂtion about that. HmmmâŚnext addiÂtion? đ
