Ford Cargo Area Badge Light Installation with Pictures

writ­ten 3/31/25, updat­ed 3/31/25

Overview

What

Installing a Car­go Area Badge Light on a 2024 Mus­tang Mach‑E

Why

For fun (had excess Ford­pass points to use!)

Time and Effort

Time: 20 min­utes

Effort: Easy

Materials and Cost

Supplies

Ford Car­go Area Badge Light

Scis­sors

Painter’s Tape

Cost

$10.55 ship­ping + tax (Used 23,800 Ford­Pass points, $119.00 MSRP)

Process

  • Open trunk
  • Remove car­go cov­er, if using

Push up on the end to get it to snap out of the hook

  • Read instruc­tions
  • Unroll the guide and cut around the out­side lines
  • Cut the inte­ri­or box as instruct­ed
  • Locate the por­tion of the trunk door inte­ri­or where it’s going to go, then tape the tem­plate onto it

The trim pan­el in the mid­dle is so use­ful to have. Just line the paper up with it, words leg­i­ble. I put the painter’s tape up and creased it out of the way for easy access because the paper keeps want­i­ng to roll up on you.

  • Find the lit­tle alco­hol pack­et that comes with the kit (I did­n’t even real­ize it came with one. D’oh!) and wipe the area with­in the cutout in the mid­dle
  • Pay atten­tion to the instruc­tions here! Locate the mount and ori­ent it cor­rect­ly with­in the mid­dle cutout. Tab to the LEFT (oth­er­wise your badge will be upside down)
  • Peel off the adhe­sive back­ing, fit it into the cutout, and press firm­ly along the length of the mount for at least 60 sec­onds

Boom, baby! Ehh, it’s a lit­tle off-cen­ter, but that’s okay.

  • Remove the tem­plate
  • Now for the hard­est part of the install: con­nect­ing the light, itself
  • Look at the bot­tom of the badge light and note the rec­tan­gle where that will fit in the tab that need­ed to be point­ed left. You have to first push that into the tab and then press firm­ly so that the hor­i­zon­tal lines snap into the grip­pers on the mount. You need to hear a bunch of clicks (Notice that it uses CR2450 x2 bat­ter­ies)
  • This is a lit­tle bit eas­i­er to say than do (at least for me), so I employed the use of the painter’s tape to give me a gen­er­al idea of where the tab was+
  • Sev­er­al clicks lat­er, VOILA!
  • Peel off the pro­tec­tive film and enjoy your new badge light!

Out­side and inside view. I won­der if the glare will both­er me…

COMPLETO!

Daifuku (Red Bean Mochi) Recipe

writ­ten 12/8/24, updat­ed 12/8/24

What

Japan­ese dessert. It’s mochi (sweet gluti­nous rice flour), a chewy rice cake, wrapped around a fill­ing, usu­al­ly anko (sweet red bean paste). Can be filled with oth­er ingre­di­ents like mung bean, fresh cut fruit, ice cream, or cus­tard, and col­ored with pow­ders (such as matcha pow­der), fresh fruit puree, or food col­or­ing.

This recipe is made in the microwave for ease, but can also be steamed

*See Notes for more details

Ingredients

1 Cup Shi­rata­mako or Mochiko Sweet Rice Flour (*See Notes)

¼ — ½ Cup Sug­ar (more or less as desired)

1 Cup Water

1 Cup Anko (sweet red bean paste, bought or made)

Katakuriko (pota­to starch or corn­starch as need­ed for dust­ing)

Supplies

Heat-proof bowl

Sil­i­cone Spat­u­la

Sil­i­cone Whisk

Plas­tic Wrap/Microwave Cov­er

Parch­ment Paper

Bak­ing Sheet/Tray

Time and Serving

Time: 5 min­utes com­bine + 2 min­utes microwave + 20 min­utes shap­ing = 30 min­utes

Serv­ing: 8 pieces

Directions

  • Pre­pare your Anko fill­ing
  • On a tray or bak­ing sheet, do the same thing and set aside (this is where you’ll put the formed dai­fuku)
  • Whisk togeth­er Flour (1 Cup) and Sug­ar (¼ — ½ Cup, to your desire)
  • Add the Water (1 Cup) and com­bine with the sil­i­cone spat­u­la until it forms a smooth bat­ter
  • Cov­er with either plas­tic wrap or microwave lid
  • Microwave for about 1.5 min­utes
  • Remove and stir well
  • Return to microwave for anoth­er 1.5 min­utes
  • It should have formed a shiny, smooth dough, a some­what hard lump, dif­fer­ent from the bat­ter from before
  • If not, then return for 30 sec­onds at a time, stir­ring in between
  • Dust your parch­ment paper work­space with either pota­to starch or corn­starch
  • Scrape the dough out onto your work­space (Be care­ful, it’s going to be HOT)
  • Sprin­kle starch as need­ed to make it less sticky
  • Divide the hot dough into equal por­tions
  • Roll them into flat disks
  • Put your Anko fill­ing into the mid­dle and pinch the ends to close them
  • Place it seam side down on your pre-dust­ed tray
  • Con­tin­ue to make the rest
  • This is best enjoyed right away, or cov­er and refrig­er­ate up to 2 days

Notes

Clean-Up Tips

  • Soak your bowls and imple­ments in water to help loosen it up
  • Try not to dump the wet flour down the drain if you don’t want to deal with a clog
  • If it’s being stub­born even after soak­ing, use the sil­i­cone spat­u­la to scrape the wet dough into the trash­can

Katakuriko = pota­to starch

Mochi vs Dan­go

  • Dan­go: term for ball-shaped foods
  • While these days the lines have blurred between the two desserts’ ingre­di­ents, tra­di­tion­al­ly, the dif­fer­ence is that Mochi was made from steamed gluti­nous RICE (grain) and pound­ed in a pes­tle, while Dan­go was made from non-gluti­nous rice FLOUR, mixed with water, knead­ed, then steamed or boiled.
  • Dan­go is made like boba, where the lit­tle balls are boiled

When made the same way (Flour, sug­ar, and boil lit­tle balls) tapi­o­ca starch (cas­sa­va) will make boba, while rice flour will make dan­go.

Mochiko vs Shi­rata­mako

  • Both flours are sim­i­lar to each oth­er but dif­fer in pro­cess­ing
  • Both can be used in oth­er dish­es like bak­ery goods and as thick­en­ing agents in savory dish­es
Mochiko
  • Ground when rice is dry
  • Less work­ing time until hard­en­ing
  • Sticky, chewy tex­ture
  • Stronger fla­vor
  • Fine­ly ground flour
Shiratamako
  • Ground when rice is wet, then dried
  • Stretch­i­er, even when cool
  • Smoother tex­ture, more del­i­cate
  • Good for refined desserts
  • Coarse, gran­u­lar tex­tured flour