DIY: Portable AC Dual Hose Window Vent Mount

writ­ten 6/27/25, updat­ed 6/27/25

Back to DIY Projects Page


What

A do-it-your­self sin­gle or dual hose win­dow mount­ing thing

Why

Had a portable AC unit and want­ed to mount it to the win­dow

Time and Effort

Time: ~1.5 hours

Effort: Easy-mod­er­ate



Materials and Cost

Mate­r­i­al

Foa­mu­lar XR 1“x2’x2’ Rigid Foam Board

HVAC Alu­minum Foil Tape

Dou­ble Reflec­tive Insu­la­tion 24“x10’

Cost

$9.97 (x2 for dual hose set­up)

$9.88

$11.97

TOTAL: $41.79

Option­al: Remove­able Win­dow Seal­ing Tape (~$10–12)

Note: as of this writ­ing, a dual hose win­dow kit on Ama­zon will cost you about $33.99; from Home Depot is $37.18. How­ev­er, you can also buy foam inserts that fit into them for $35.99 because, appar­ent­ly, the kits don’t keep out heat as well as you’d think.

Owned Sup­plies

Mask­ing Tape

Painter’s Tape

Tape Mea­sure

Sharpie

Scis­sors

Foam Knife

Util­i­ty Knife

Square

Vent Tem­plate


Process

Measurements

Ori­ent the AC unit and fig­ure out how hoses should be placed to fig­ure out how much of the open­ing you’ll need to fill will the vent mount. Take your mea­sure­ments which will tell you how much mate­r­i­al is need­ed.

My win­dow is 31″ x 58″ (W x H), with each open­ing about 28″. I’m work­ing with an Ecoflow Wave 3 for which the hoses have 2 slight­ly dif­fer­ent open­ing sizes. After ori­ent­ing the machine and hoses for the space avail­able, I knew that I need­ed the win­dow to be open about as much as it can be.

NOTE: For a dual hose unit, try to place the exhaust hose high­er than the intake hose since heat ris­es, and air under the hot­ter expelling air should be cool­er. For a sin­gle hose unit, you won’t need to open the win­dow as much


Materials

Gath­er any owned equip­ment, then pro­cure nec­es­sary tools and mate­ri­als (I ran out to Home Depot)

Note: My win­dow has a screen, so I left it down and placed the vent hoses on the oth­er side. If yours does not have a screen, it would prob­a­bly be a good idea to fac­tor in a mesh screen to pre­vent bugs enter­ing the hoses when not in use. Prod­ucts like Fiber­glass Mesh Rolls, or Vent Mesh Rodent/Bird Screens are options.


Fitting

With sup­plies in hand, test the Rigid Foam Board on the win­dow. Mine was best sit­ting inside the lip of the win­dow jamb. If more mate­r­i­al is need­ed, mea­sure and mark with the Sharpie. Secure the foam board in place (either low­er the win­dow onto it, or use mask­ing tape), then place each vent hose in its desired spot and trace with the Sharpie


Cutting

Time to make cuts! Depend­ing on cut­ting loca­tion, make sure to put down a drop cloth, news­pa­per, or oth­er cov­er­ing for easy cleanup. The foam pieces will get every­where

First off, I put togeth­er the main win­dow pan­el by cut­ting the piece to make it whole using mea­sure­ments (in my case about 8in). I used a Square and a Util­i­ty Knife to score both sides, then all that’s need­ed is a lit­tle bit of force to snap the piece off (I just used the edge of a chair for lever­age)

Next are the holes! My Ecoflow hap­pened to come with a Vent Hole Tem­plate, so I used Mask­ing Tape to adhere that to each traced hole

I’m sure a jig­saw would be the eas­i­est and clean­est way to accom­plish this, but I was­n’t about to shell out anoth­er $200 for that (maybe at some point in the future).

So, I used a Util­i­ty Knife to cut the cir­cu­lar shape. Because the foam board was too thick for just the util­i­ty knife, I poked holes with a ran­dom tool (can be a screw­driv­er) and con­nect­ed the lines with a Sharpie.

Then with the util­i­ty knife, I cut the round pat­tern and a cross pat­tern on either side to facil­i­tate removal

At this point you can use any vari­ety of meth­ods to chip away at the foam (e.g. mal­let, screw­driv­er, knife). I end­ed up using a Craft Knife to deep­en the util­i­ty knife cuts all the way around, and it was excel­lent for smooth­ing out the holes

Mal­let

Craft Knife

Super easy to trim any excess pieces this way

Assembly

Back upstairs! First up: make sure the main pan­el pieces fit into the win­dow. Next, dry fit the hoses. Used the craft knife to make some adjust­ments.

Anoth­er dry fit of all pieces. Looks good!

Had the hoses ori­ent­ed the wrong way at first

Now to con­nect the two pieces of the main pan­el with the HVAC Alu­minum Foil Tape. I’ve nev­er used that kind of tape before. It’s like putting on a vinyl where you have to peel away the back­ing. When attached, the hold feels extra strong, so be care­ful not to rush and mess it up.

After anoth­er dry fit

Exhaust above inlet because heat ris­es

Mov­ing on: now to adhere the Dou­ble Reflec­tive Insu­la­tion. This real­ly is an option­al thing, but I want­ed to do this because man­u­fac­tur­er word­ing on the rigid foam boards notes that its only rat­ed to 75F. Giv­en the beat­ing sun and 100F heat, I want­ed some­thing else to both block heat and afford a lit­tle more weath­er resis­tance to the pan­el.

Fun Note: The mate­r­i­al is just like sun­shades for a car. One of the favorite things I’ve ever bought are cus­tom dri­ver and pas­sen­ger win­dow shades for my car, and it lit­er­al­ly uses the exact same mate­r­i­al except with an edge lin­er to look pret­ty

To attach the insu­la­tor, use Mask­ing or Painters’ Tape (painter’s is eas­i­er to remove) to adhere the mate­r­i­al to the foam board, then cut to size. Then, use the HVAC Tape to secure it to the foam board.

Make sure you’re apply­ing it to the prop­er side!

NOTE: This will add some width to the foam board, which isn’t nec­es­sar­i­ly a bad thing, but if it’s too tight, you may have to trim some off the foam. I left mine the way it was and just jammed it in there. It was a tight fit, but that works for seal­ing out weath­er and bugs. It is foam after all and will com­press a lit­tle.

Cut the vent holes out with scis­sors. I left a lit­tle bit of excess mate­r­i­al around the open­ing for a lit­tle more bug/weather bar­ri­er.

Left a lip on pur­pose
Hose dry fit

Lat­er, I end­ed up secur­ing each hole with 4 pieces of HVAC Tape because I real­ized that air move­ment might bal­loon out the space between the insu­la­tion and the foam board.

That lit­tle space between the foam and the insu­la­tor is just ask­ing for air to flow into it, bil­low­ing things out
Taped it up

Finishing Up

We’re pret­ty much done at this point! Go ahead and place it all into the win­dow, place all the hoses, and check out your hand­i­work!

You can see the win­dow screen I left in place to help with bugs
Every­thing fits snug­ly

The only thing left to do is to seal the cracks around the foam board and the vent hoses.

I used Mask­ing Tape for easy removal, but if you want some­thing bet­ter, buy some Remov­able Win­dow Seal­ing Tape (XFas­ten brand on Ama­zon is $11.99, appears to be based in Flori­da).

DONE!

Fin­ished!
Out­side view
When you want to remove it quick­ly, just pull the mask­ing tape

Notes

  • The whole sys­tem works well, and removal is as easy as remov­ing tape
  • Sound is a prob­lem, though. I can hear every­thing out­side. Like birds in the morn­ing. When you’re get­ting your best sleep. I con­sid­ered some sound­proof pan­el­ing to put in front of it but then real­ized that I don’t use the unit too much unless there’s a heat wave. Not only that, but the pan­els are pret­ty expen­sive.
  • It also makes my room smell like an attic with all the out­door smells. Per­haps it would be dif­fer­ent if I’d used the Win­dow Seal­ing Tape?

Back to DIY Projects Page

DIY: Bed Canopy Frame with PVC

writ­ten 6/17/24, updat­ed 7/28/24

Back to DIY Projects Page

Overview

What

Mak­ing a DIY canopy frame over a bed with PVC

Why

Cool­ing. To trap A/C from floor reg­is­ter under­neath a canopy dur­ing sum­mer. Room is top floor of a 3‑story town­house. Can be use­ful for trap­ping heat in the win­ter, too.

Time and Effort

1 per­son project, 2 would be help­ful

Time: 1 hour

Effort: Easy

Materials and Cost

4ft 1″ PVC Pipe (your choice of PVC size and height)

PVC Fit­tings (depends on how many con­nec­tions you want)

Canopy Mate­r­i­al

Fab­ric Fas­ten­ers (ties/clips/hooks/attachments)

Tem­po­rary Secure­ments (option­al, but rec­om­mend­ed)

$93.99 (20 piece)

$24.86 (14 total)

$39.99

$14.99 (25/pack)

$15.98 (Qty: 4)

Oth­er Sup­plies: Ratch­et­ing PVC Cut­ter ($14), Dri­ver, Drill Bits

Total Cost: $189.81

PVC Fittings

For this 6′ x 4′ x 6′ canopy, I bought 4′ long PVC at 1″ width (you can choose oth­er sizes and lengths) and used the ratch­et­ing PVC cut­ter to cut the pieces to 2′ to cre­ate 6′ lengths. T

Fit­tings need­ed for the 1″ PVC

FORMUFIT, a com­pa­ny that spe­cial­izes in fur­ni­ture-grade PVC sells all of these plus more options in many col­ors. 100% USA made. I bought every­thing but the 3‑way elbows at a local big box store in the PVC aisle because FOR­MU­FIT’s prod­ucts come in packs of 10.

  • 3‑Way Elbow (4 qty)
  • 90-Degree Elbow (4 qty)
  • Exter­nal Cou­pling (4 qty)
  • Stan­dard Tee (4 qty)

Option­al Foot­ers

I did­n’t do this, opt­ing for cross­bars favor­ing sta­bil­i­ty, but using a Reduc­er Cou­pling can work as pipe feet

Schematics

Here’s a hand-drawn dia­gram show­ing dimen­sions. This is 6′ x 4′ x 6′ (L x W x H) or 72″ x 48″ x 72″.

For ref­er­ence:

Bed Size (USA)Dimen­sions (L x W)
Twin75 in x 38 in (6¼ ft x 3⅙ ft)
Twin XL80 in x 38 in (6⅔ ft x 3⅙ ft)
Full75 in x 54 in (6¼ ft x 4½ ft)
Queen80 in x 60 in (6⅔ ft x 5 ft)
King80 in x 76 in (6⅔ ft x 6⅓ ft)
Cal­i­for­nia King84 in x 72 in (7 ft x 6 ft)

Why 4′ width when a twin bed is only 3⅙’ wide?

In this instance it’s to try and cap­ture the cool air blow­ing from the floor duct reg­is­ter, under the over­hang­ing side

Cutting the PVC

There are many options! And they most­ly depend on what’s avail­able in your house, how much you want to spend, how much time you mind spend­ing, what mess you want to make/clean up, and future use­ful­ness of any new­ly bought tools (or will it just sit in a box some­where for the rest of your life). Options include any­thing that cuts from man­u­al saws to pow­ered saws to ded­i­cat­ed PVC cut­ters.

Method 1

My first go-to was the Cord­less Mul­ti-tool I’d bought but had yet to use.

Clamped and ele­vat­ed
Cut­ting!
Whoops. Cut line and drawn line are not match­ing!
Messy and very rough edges

VERDICT: It will CUT. But it will also make a mess, cre­ate rough edges, time con­sum­ing, and requires clamps, and it took me a while to fig­ure out if there’s a best blade to use for PVC.

Method 2

I decid­ed to buy a Ratch­et­ing PVC Cut­ter for $14

Mea­sur­ing!
Line ‘er up!
Watch the ratch­et­ing mech­a­nism work
Super smooth edge and NO mess!

VERDICT: It will KEAL and lac­er­ate the PVC. This method is supe­ri­or. No set­ting up, no mess at all, smooth edges, and super-fast. No pow­er source

Assembly

Well. There’s not much to say here. You push the pipes into the fit­tings and form them into what­ev­er shape you want. The hard­est part is hold­ing them in place while you fit more. This is why a 2nd per­son could be use­ful. I did it by myself.

Fastening

Now, this is option­al, espe­cial­ly if your struc­ture will be a tem­po­rary one. Before putting them togeth­er, I mulled over this a lot. If the shape you formed is sol­id, you like­ly don’t need to secure the parts as they’re pret­ty tight just dry-fit­ted. How­ev­er, you have the option of cre­at­ing per­ma­nent or secure-yet-tem­po­rary bonds.

Permanent

Many choic­es out there, but THIS is your tra­di­tion­al plumb­ing primer and cement. Sim­ply fol­low the direc­tions and prime then cement.

Make sure to use in a well-ven­ti­lat­ed area and beware the pur­ple stain­ing of objects and flesh

Secure-Yet-Removable

There are dif­fer­ent meth­ods of doing this: You can use a screw, you can use wood dow­els, I read some­thing about using rub­ber hos­ing, heck you can use tape if you want to. I test­ed out a method that’s sim­i­lar to the oth­ers, just a lit­tle fanci­er.

I opt­ed to try Quick Release Pins. They’re a bit pricey for a project like this that would need many to ful­ly secure, and it was dif­fi­cult to find a size that would not be too long. In the end I only installed the 2 that I bought.

You also need a drill, drill bit, a stool, and a vac­u­um because it will make a mess.

Seems to fit!
Chose the drill bit
Drilling and mak­ing a mess
Hole through and through (drilled from both sides)
Insert­ing!
Aaaand it does­n’t actu­al­ly fit through it.

While the first pin could not ful­ly engage the hole (per­haps I drilled it at an angle instead of straight through), the sec­ond one did. Advice: err on the larg­er side when choos­ing a drill bit. I had to use the bit to ream out the open­ing from many angles just to get the pin to fit

Suc­cess!

The pin secures the pipe to the fit­ting, ensur­ing that it will not come apart. The only flaw in this is that if you use many fit­tings, that’s a lot of secure­ments! I chose the top cor­ners of the frame as it would pre­vent the ends from bow­ing out if the canopy mate­r­i­al end­ed up being too heavy for the frame.

Canopy

This part, I’m still not super hap­py about. It was hard to find any canopy curtain/top/fabric at all, let alone one that appealed to me. Aside from sewing one myself from a cho­sen, ide­al fab­ric (which I may end up doing in the future), I end­ed up choos­ing a can­vas tarp. My orig­i­nal idea was to use an old fit­ted sheet. I did­n’t con­sid­er how slip­pery the PVC is and after about 15 min­utes of wran­gling, I gave up. Plus, how would I secure the fit­ted sheet? The can­vas tarp was not only as thick as I want­ed it to be, but it came in a white col­or. If I want to trap cool air, I don’t want it to absorb heat as a dark­er col­or.

Assem­bly

8′ x 10′ seems large, does­n’t it? It kind of is… I thought that hav­ing the extra length would make it eas­i­er to drape and less like­ly to slip off. Also, that way, I can let the sides down as I please. Lat­er, I thought about spi­ders mak­ing webs in the folds…

Then a new prob­lem arose:

THE CORNERS

What to do? How to fas­ten? To this day, I don’t real­ly know the best option apart from cut­ting it and sewing it togeth­er (which would bring me back to square one with the canopy). I just kind of did some­thing.

Does it Work?

After all of that, does the canopy work? Does it trap cool air? I have to be hon­est, I’m not ful­ly sure! I think there is an improve­ment, yes, but it’s still not an end-all solu­tion. On the very hot days, I was hot and stuffy and found it hard to sleep. Low­er­ing the sides did make a dif­fer­ence, and I also end­ed up buy­ing an Air­tight Rip­stop Nylon Fab­ric think­ing that per­haps the tarp, which was made to be breath­able, was TOO breath­able.

HOWEVER. I do have a FLIR cam­era, so here are two inter­est­ing FLIR images (note: these images were tak­en before the addi­tion of the air­tight fab­ric on top):

A/C reg­is­ter behind the bed in the image (where the blue is)
A/C reg­is­ter to the RIGHT of the image

Blue is cool and yel­low is hot. The A/C reg­is­ter is on the right side of the right­most image. There IS a cool­ness to the canopy com­pared to the area out­side of the canopy. So, yes, in a word, yes, I think it does work.

VERDICT: Yes. It does trap cool air and main­tains cool­er tem­per­a­tures than the sur­round­ing air. Hav­ing a fan to fur­ther direct the air com­ing from the reg­is­ter might make it more effec­tive at cool­ing.

Back to DIY Projects Page