Homemade Deli Meat – With and Without Ham Maker

written 4/15/2024, updated 7/21/2025

The juices that came out of this… YUM

What

Making deli meat at home by combining different cuts of meat (can be same kind of meat or a mixture) with and without a Ham Maker

Why

Ability to control what’s put inside your own cold cuts, and can be cheaper

Time and Effort

Time: A few hours

Effort: Easy

Ingredients

Meat

Seasonings

Supplies

Mixing Bowls

Cutting Board

Knives/Meat Grinder/Processor

Ham Maker

Plastic Wrap/Sausage Wrapping

Foil

Pot/Rice Cooker/Oven

Ham Maker Method

Using a Ham Maker is really the easiest way to make a formed meat, especially if you want to mix several cuts or meats together. It can also be used without mixing meats or grinding them. Ham Makers make the wrapping step a cinch.

Ham Maker

Ingredients and Supplies

Meat, Seasonings, Water, Ham Maker, Cooking Bag, Tall Pot, Pot Thermometer, Stove, Refrigerator

Time

30 minutes Prep + 2 hours Cook + overnight Chill

Process

  • Wash your Ham Maker if you haven’t
  • Fill a tall pot with Water, and heat it up on the stove (Target: 182-195F)
  • Choose your meat:

Whole Meat – an entire piece of meat, uncut (e.g. pork loin, pork shoulder, whole breast)

Mixed Meat – a formed mash of different cuts or combinations of meat types

  • Prepare your selection by removing veins, bones, and sinews. Decide if you want to keep, and how much, any fat
  • If using a meat mixture, chop, mince, grind, process, or any combination as desired
  • Season your choice of meat, to taste
  • Allow to set for a few minutes
  • In the meantime, line the Ham Maker with a Cooking Bag
  • When ready, place meat into the canister
  • Twist the top of the bag closed
  • Close the Ham Maker with the press and lid, then insert the thermometer
  • When water in the pot reaches between 180 – 195F, place the full Ham Maker in the water, making sure the water level sits above the fill line of the meat inside
  • Keep the temperature steady (I set my gas stove low-medium)
  • Cook until internal temperature reaches the safe cooking temperature for your meat choice, about 2 hours
  • Place the hot Ham Maker on a hot pad in the refrigerator and cool overnight
  • When fully cooled, run canister under warm water to release the meat

Slice and Enjoy!

Pictures!!

Chopped, Minced, and Processed
Removing Air Bubbles
Squish
It’s Hot!
Chilling
Opening
Pour out the juice
Release
Still in Bag
There it is!

Ta-DAAA!! The hole is where both the twist top of the plastic and the thermometer when in. You can see the texture differences from the different cuts/processing of the meat. Delicious!

No Ham Maker Methods

Sous Vide and Smoked are two methods of making this. If you don’t have a sous vide device, there are alternatives

Sous Vide Method

There are different ways to sous vide without actually using a sous vide device. You can use an oven, a Dutch oven or a pot, and even a rice cooker.

Ingredients and Supplies

Meat, Seasonings, Mixing Bowls, Water, Pot/Oven/Rice Cooker, Thermometer, Refrigerator

Time

35 minutes Prep + 2 hours Cook + Chill

Prepare Meat

*Pictures below

  • Remove any veins, sinews, and bones. Remove or use fat as desired
  • Choose your meat:

Whole Meat – an entire piece of meat, uncut (e.g. pork loin, pork shoulder, whole breast)

Mixed Meat – a formed mash of different cuts or combinations of meat types

  • If using Mixed Meat, prepare a [diced: minced: ground] meat ratio of [¾ : ½ : ⅓ lb] or [350 : 250 : 150 g]
  • Season the meat, to taste (If desired, season each texture a bit differently for a combined complex flavor)

Wrap

  • Set out a double layer of plastic wrap and sprinkle half with smoked paprika and whatever else you’d like
  • Turn out meat mixture
  • Tightly roll into desired shape and size

NOTE: Make sure wrapped meat log(s) will fit into your cooking implement so it can be covered in water!

  • Secure the ends

Cooking

Here are 3 methods of cooking the meat ham without dedicated Sous Vide equipment

Pot Method

  • Fill with water
  • Bring water to a boil
  • Place meat log into the water (make sure meat is and will be fully submerged the whole time)
  • Bring to a boil again
  • Turn off heat and place lid tightly on top
  • Leave for 45 minutes to 1 hour
  • Check for doneness with thermometer
  • Repeat if necessary
  • When done, let cool and enjoy, or chill in refrigerator

Oven Method

  • Preheat oven to 215 – 220F (100C)
  • Select a deep dish or oven safe pot
  • Boil enough water to fill
  • Pour in boiling water
  • Place meat log
  • Cover with parchment paper
  • Cover that in foil and/or a tight lid
  • Cook for 1-3 hours until 160F (75C)
  • Remove from oven
  • Place in an ice bath and/or refrigerator until internal temperature is 50F (10C)

Rice Cooker Method

  • Boil water
  • Pour boiled water into rice cooker
  • Using a thermometer, mix in cold water until water temperature is somewhere between 175-195F
  • Place meat log into water
  • Close
  • Set rice cooker to Keep Warm
  • Cook for about 2 hours
  • Be sure temperature is safe for choice of meat
  • Let cool then enjoy or chill in refrigerator

Pictures (Oven Method)

Ta Da!! Taste was ON POINT

Smoker Method

This method uses a meat grinder then a meat smoker. You can use a dedicated meat grinder, a meat grinding attachment for a stand mixer, or even just a food processor

Prepare Meat

  • Decide on ratio of meat cuts (e.g. [½ : ½] ratio of [skinned chicken thigh : skinless chicken breast])
  • Cut into small pieces

Grind/Process

  • Grind/Process 1st time
  • Grind/Process 2nd time
  • Add any desired seasonings and half of total water

NOTE: For 1lb of meat, add 20ml (⅔ oz. or 1⅓ Tbsp) of water

Total ratio is 40mL water per 1lb (40mL = 1⅓ oz = 2¾ Tbsp)

  • Grind/Process 3rd time

Wrap

  • Place ground meat in a mixing bowl
  • Add the rest of the water, and then mix together really well (should be very sticky)
  • Pump or stuff into an edible or inedible casing (100mm is the largest size I could find on Amazon)
  • Secure the end

Cooking

Overview: 1 hour Dry + 1 hour @ 130F + 1 hour @ 145F + 1 hour @ 160F + more @ 175F

Total: ~5 hours

  • Set smoker to 120F (50C), NO smoke, NO humidity, OPEN dampers to dry the casing for 1 hour
  • Set to 130F (55C), ADD smoke, ADD humidity (water pan), ¾ damper for 1 hour
  • 145F (65C) for 1 hour
  • 160F (72F) for 1 hour
  • 175F (75C) until internal temperature reaches 160F (72C)
  • Place in an ice bath to separate the casing and the meat

Slice and enjoy!

Notes

Attempt 4/14/24: Used Oven Sous Vide Method. Should have added something like cornstarch in the meat mixture to give it some adherence. That and/or changing the ratio to add more ground/pureed meat to fill in the gaps in the meat, while taking away from the original cubed meat. Even if cubing (altered the recipe directions to use smaller pieces), then should process a little. 3 degrees of food processor chopping to make the final product smoother would be more ideal. The way this ended up was more of a headcheese. There IS an obvious complex texture, but it all fell apart easily. The 3 different flavor profiles gave it GREAT taste. Made the mistake of not thinking about the cooking vessel until after rolling the meat. Should have cut it in half and then would have been able to have 2 smaller hams and able to cook it inside of the Dutch oven with the water filled to the top. The way I had it, the water didn’t even cover the whole meat log, so cooking was very uneven. Unsure of how to test internal temperature of meat log without making a mess. Cooking @ 215F took about 2.5 to 3 hours total. Used way too much plastic wrap and wasn’t able to use a lidded dish, just 2 layers of foil. Meat used: Chicken. 3 thighs, 1.5 breast, ¼lb ground chicken (hand squeezed to pulverize). NEXT TIME: more ground chicken, less cubed breast. Add cornstarch for smoothness and adherence. Smaller logs for more even cooking. More food processing. Maybe try using meat casing.

7/21/2025: Used Ham Maker

  • Sous Vide cooking charts recommend cooking chicken at 150F for 1-3 hours.
  • A Ham Maker is a MUCH easier method of doing this. It’s a metal contraption with a spring in it that fits right into a stock pot on the stove and does the same thing neatly. However, if you don’t have one and don’t want one, this is fine, too.
  • There’s always the option of baking or broiling it after the fact for a possible crust or rind? Haven’t attempted that yet

DIY: Solar Powered Wildlife Waterer/Birdbath

written 6/17/24, updated 6/27/25

Overview

What

DIY fountain with small water pump for moving water

Why

Water aeration not only prevents stagnation but also kills mosquito larvae. Birds and other wildlife enjoy drinking and occasionally bathing in it

Time and Effort

1 person project

Time: 30 minutes, more for paint

Effort: Easy

Materials and Cost

*8″ Deep Plant Saucers (whatever size you want)

*Plastic Round Bird Feeder Bowl

6W Mini USB Solar Panel 5V/1A

5V USB Submersible Water Pump with Tubing

Outdoor Acrylic Paint and Brushes

Outdoor ModPodge

Your choice of stand/pole mount/holder

$16.99

$11.99

$13.99

$9.99

$20

$6.99

$18.99

I already had the paint, brushes, Mod Podge, and submersible pump, plus a coupon, so my total cost is different than the total cost of supplies

Other Supplies: Driver, Drill Bits, Rock(s)

*Optional or In-Place-Of: 3D Printed bowl and/or tray is the easiest and cheapest method if you happen to have one

Total Cost: $98.94

My Cost: $56.36

Bird Bath Holder options:

  • Pole-mount dish
  • In-ground dish holder
  • Deck rail-mounted dish
  • Free-standing holder
  • Or just on the ground

Process

This originally started as a birdbath, but not only was it too small to be a birdbath, but none of the animals used it as that. They were more interested in drinking the water, so now it’s a Wildlife Waterer. Occasionally, the camera aimed at it will catch a bird bathing in it

Schematic

Drill Holes in Upper Tray

Drill Holes in the plastic bird bowl (smaller holes for water passage, big for the tube), and a notch for the power cord.

You can place the water hose in the center or offset depending on your preference

*3D Printer

Easiest and cheapest method if you happen to own a machine

If using 3D printer, I’d recommend this BOWL customized to your specifications (reduced the thickness). You can add a little notch for the power cord.

When in doubt choose a dark color (prevents light penetration which allows algae to grow). My design allows for the system to be easily taken apart and cleaned. The reason there’s a reservoir of water that houses the pump underneath the tray is that offering animals toxic algae or fungus-infected water can kill them.

The little tabs are optional
The tray had broken over the winter just enough to allow the cord to pass through.

Paint

If using clear saucers/bowl, paint outer layer (use 3 or 4 layers as they are so thin). Darker are better colors to prevent algae.

Note: Apparently, birds are attracted to either their own plumage colors or for the shy birds, neutral colors like drab green, gray, and brown. Birds supposedly dislike white.

Assembly

Because I was using cheap saucers, I stacked them 3 or 4 deep (for strength). Then, the submersible pump goes on the bottom. On top of that, place the drilled bowl to create separation from the motor, passing the tube and cords through their respective holes

Fill with water

By the Power of the Sun

Connect the male USB of the submersible pump to the female USB on the solar panel (or however your power hookup is) and test out the water flow.

Interesting Note: there must be enough light to start the motor, but subsequent power requires much less (physics!). Meaning, even though direct sunlight is needed to start the pump, indirect sunlight (part shade) is okay for continuous operation

Connect the cables

Power!!!

Starting ‘er up!
Sun on! Sun Off!

Tube Orientation Options

  • Cut the tube shorter
  • Place a little aerator on the end and drill small holes in the top of the tube to create a sprinkler effect
  • No tube, just pure aeration

Long Tube – water current

Without Tube – lots of bubbles

Short Tube

I was testing stuff out on a heated waterer I bought later after making mine

Aerated Short Tube

The aerator is just a random thing I found outside on the ground while walking the dog. It just so happens to be the right size and flexibility for the hose. If you look up “Rubber Silicone Round Plugs” you’ll see several of them. Like THIS

Additions

Place decorative rocks or plain rocks so that bees and smaller birds can perch safely

Get (or 3D print) fountain nozzles for fun sprays

Cleaning!!!

You MUST clean these! As stated above, algae blooms are toxic to animals. Similarly, if too much debris rots in the waterer, fungus can also infect the animals. Warm water and soap. If using rocks, I’ll brush them with a brush. Let them air dry, then return them to the critters

Nasty algae. When cleaning, my paper towel turned red. Red algae blooms are extremely toxic. Not just for the wild critters, but also my dog who likes to lick stuff all the time

Finished!