DIY: Wood Porch Package Shelter with Solar Powered Camera

writ­ten 6/8/26; updat­ed 6/15/26



Overview

What

Shel­ter for pack­age deliv­ery

Why

Cov­ered area from the ele­ments for pack­ages

Time and Effort

Time: 2–3 Days

Effort: Mod­er­ate


Supplies, Equipment, and Cost


Bought Mate­r­i­al

Exte­ri­or Wood Screw Ass­rt Kit

Min­wax Wood Filler 16oz

XL Rec­tan­gu­lar Feet Rub­ber Bumpers

(0.59″ H x 3.00 L x 1.51″ W)

#10, 1½” Truss Head Wood Screws (80ct)

Tapo C400 Solar Out­door Cam­era Kit

Goril­la Water­proof Patch Seal Spray (x2)

Varathane One Step Stain+Spar Exte­ri­or

Sand­ed Ply­wood 23⁄32″ x 2′ x 4′ sheet

Woost­er Short­cut 2″ Paint­brush

Cost

$15.99

$11.98

$16.99

-

$9.99

$49.99

$29.92

$29.98

$28.20

$7.47

Total

$200.51

Owned Sup­plies

1x4 Wood

2x4 Wood

1x2 Wood

Masks

Eye Pro­tec­tion

Gloves

Hear­ing Pro­tec­tion

Impact Dri­ver

Drill Dri­ver

Cir­cu­lar Saw

Driver/Drill Bits

Wood Screws

Cord­ed Sander

Sand­pa­per

Squares

Pen­cil

Mea­sur­ing Tape

Spac­ers

Clamps

Work­ta­bles

Wet/Dry Vac

Option­al: Spring Loaded Cen­ter Punch, Rub­ber Shims


Schematics, Measurements, Wood Needed

These are the mea­sure­ments I end­ed up with. Feel free to make it to any desired dimen­sions for your space

Sor­ry, I’m ter­ri­ble at draw­ing per­spec­tive

Wood Used

Type/Size

2x4

1x4

1x2

-

Ply­wood 2′ x 4′ x

23⁄32″ Sheet

-

-

Misc

Length

22¼”

18″ & 14″

14″ & 22¼”

20½” & 1½”

18⅜” x 17″

6″ x 17″

4½” x 10½”

4½” x 7⅝”

4½” x ¼”

Amount

x4

x4(18″); x2(14″)

x2(14″); x2(22¼”)

x1(20½”); x3(1½”)

x1

x2

x1

x1

x1

Total Length

89″ (7.42′)

100″ (8.33′)

-

97½” (8.125′)

-

-

-

33.375″ (2.78′)

Scrap

Sum­ma­ry

Wood Prod­uct

2′ x 4 ‘x 8’

1′ x 4′ x 8

1′ x 2′ x 8

2′ x 4′ x 23⁄32″ Ply­wood Sheet

Amount Need­ed

1

1 + 0.33″ *

1 + 0.125″ *

1

*NOTE: So, could buy more or use just a lit­tle less in the the under­body and any place nobody will notice


Process

Dis­claimer: I am NOT a pro­fes­sion­al, just an ama­teur DIY­er. This is chron­i­cling how I went about com­plet­ing this dreamed-up idea

Planning, Measuring, Gathering Materials

  • Con­sid­er mea­sure­ments, dimen­sions, over­all shape, and any sup­port pieces need­ed for the desired loca­tion
  • Gath­er nec­es­sary mate­ri­als and equip­ment
  • Decide if a secu­ri­ty cam­era is desired: where/how to mount it, pow­er source, abil­i­ty to rotate remote­ly, stor­age options, sub­scrip­tion options, cord length, etc.
  • Decide upon fin­ish: stain/paint, seal­er, water­proof­ing, etc

Dry Assemble

  • Since it was going to sit out­side in the ele­ments, I want­ed to ele­vate it off the ground as well as pro­vide air­flow and drain­ing since it’s wood after all. For the spac­ers, I used some ran­dom pieces of dou­ble reflec­tive insu­la­tion that hap­pened to be the right size
  • Test­ing out the sup­ports and try­ing to decide if I want­ed them on the ground of rest­ing on the bot­tom cross-pieces

Plywood Cutting

SAFETY FIRST! It is high­ly rec­om­mend­ed to use eye pro­tec­tion, gloves, shoes, and hear­ing pro­tec­tion when using pow­er tools. You can even wear an apron to pre­vent a mess on your clothes. Also, cut­ting wood makes a huge mess, so plan accord­ing­ly.

Roof Panels

  • Ooo, this part made me real­ly ner­vous. The tricky part was try­ing to mea­sure how much is need­ed to have a straight mansard style roof (at least I think that’s what it’s called) that I was plan­ning for the project. After a lot of uncer­tain­ty, I just went for it.
  • I decid­ed to cut the side pieces first before the main large mid­dle piece. You can see in the right­most image that I was try­ing to cal­cu­late how much I’d need for the mid­dle one.

This unfor­tu­nate Spot­ted Lantern­fly nymph was in the way of my cut mid­dle roof pan­el and got squished.

Miter (Angled) Cuts with a Circular Saw

  • I don’t have a miter saw any­more. When I moved, I got rid of my nice com­pound miter saw thanks to lack of space and use. With no desire to buy a new one ($200–500!!), I found out that you can actu­al­ly use a cir­cu­lar saw to make angled cuts!!
  • Just find the release, set the angle, and voila!

Check that angled cut!! This was 45 degrees

  • With boost­ed con­fi­dence, I went ahead and made all the cuts that I had mea­sured out before, angled includ­ed, with the help of a speed square
  • Mis­take #1: Spa­tial stuff is not my forte. As it turns out, two 45-degree sur­faces togeth­er make a square… Which is not what I was going for. What I want­ed was a 45-degree sur­face mat­ed with a 90-degree sur­face. Whoops.
45-degrees mat­ed with 45-degrees
45-degrees mat­ed with 90-degrees

This image shows how the side pan­els have 90-degree sides and the mid­dle pan­el has 45-degree cuts.

  • Let’s set that aside for a lit­tle bit

Assembling the Base

  • Lay out and ori­ent the base as planned, ensur­ing the spaces are cor­rect
  • Flip it upside down, care­ful­ly, and fix the spac­ers again, mak­ing sure every­thing is ori­ent­ed cor­rect­ly (use a pen­cil to mark the wood)
  • Dry-fit the rub­ber feet to desired ori­en­ta­tion. I chose the long way

Note: Giv­en the size of my struc­ture, if I were to do it again, I’d spring for anoth­er 2–4 rub­ber feet. As I only have 4, if you push back­wards on the struc­ture, it tilts until it hits wood instead of being as sta­ble as I’d like it to be

  • Secure every­thing with clamps so they don’t move around
  • Grab screws (I used #8 ‑1¼” wood screws for the wood which comes with a bit)
  • Get the dri­ver with drill bit and impact dri­ver
  • Mark holes, mak­ing sure to leave room for the rub­ber feet
  • Secure the base togeth­er by first drilling pilot holes, then dri­ving in the screw
  • Secure rub­ber feet using appro­pri­ate­ly sized screws (mine were #10, 1½” Truss head Wood Screws)
  • Option­al­ly, use a spring-loaded cen­ter punch to help mark the holes

Secure Supports

Time to add the roof sup­ports. This not only holds the roof, but also adds sta­bil­i­ty to the base

  • Clamp to work­space
  • Decide where screws will go, and mark them
  • Drill pilot holes, then dri­ve in the screws with the impact. Don’t sink them into the wood until every­thing is in place. Can’t stress the pilot hole enough here.

Note: you may need to get cre­ative with the clamp if you don’t have one long enough. I end­ed up drilling one hole, then insert­ing one screw to bet­ter hold the wood in place to dri­ve in anoth­er before doing the rest


Assembling the Roof

  • Mis­take #2: Mis­cal­cu­la­tion of roof pan­el sizes

Yeeaaaaah… It’s too short (at this point, I’d already secured the pan­els togeth­er. I did­n’t write that out yet, because the sizes are wrong)

  • Now that I’ve com­plet­ed the project, I can now tell you that for the 26⅜” span of the com­plet­ed roof, I need­ed 6″ side pan­els x2, and an 18⅜” pan­el for the mid­dle. That’s a total of 30⅜” length of ply­wood (so, 26⅜ : 30⅜ ratio, which is an increase of 4″ com­pared to the span)

My Fix

  • Instead of hav­ing to cut a dif­fer­ent piece alto­geth­er, I decid­ed to do a bit of a Franken­stein job. The cos­met­ics would­n’t mat­ter for the roof, as I already planned to cov­er the entire thing with a rub­ber water­proof­ing
  • So, I cut an addi­tion to the mid­dle roof­ing piece, angled to attach togeth­er into a flat plane
  • After mulling over how to secure any of the roof to the struc­ture, I decid­ed to use a tech­nique that you nev­er see used in con­struc­tion of a roof for a good rea­son. Basi­cal­ly, I used pock­et holes to secure the miter-cut pan­els togeth­er and used wood glue to improve adhe­sion. With my lack of wood work­ing expe­ri­ence and skill, my attempt at this was pret­ty bad, but hey, it worked. See for your­self:

Assembling the Rest of the Roof

  • After some dry-fit­ting, more cuts were made, uti­liz­ing scrap wood to help sta­bi­lize the clamped struc­ture for trim­ming

It looks sooo baaaad. And it was hard to line the holes up. Again, pilot holes are 100% a must!!

  • After I real­ized that I’d made an error in the mea­sure­ments, I had to back out some of the screws, and then screwed in only 1 of the side roof sec­tions to the struc­ture to facil­i­tate the addi­tion of the rest of the roof and mea­sure­ments
  • Some dry-fit­ting, more cuts, uti­lized scrap wood to help sta­bi­lize the clamped struc­ture for trim­ming
  • To secure the big, heavy piece to the rest of the struc­ture, I need­ed to get cre­ative with how I’d sta­bi­lize it all to drill into the sup­ports
I used a chair, a buck­et, and many pieces of scrap wood
  • I used the Glue-and-Screw method along with longer screws, know­ing full well that all the weight would be press­ing into these 4 sup­ports
Glue
Screw
Real­ly long screw. It’s super hard to dri­ve in straight, so I just used 1 per sup­port and tried my best

Tip: I used a method where I would drill pilot holes, then dri­ve a screw part­ly in just so the tip sticks out, which can there­fore be “caught by” a pilot hole, then impact­ed in the rest of the way. This is help­ful if you have dif­fi­cul­ty see­ing how the holes line up togeth­er. You can see this in the mid­dle image above

  • Roof com­plete! It ain’t pret­ty, but it works!
Very bad look­ing
But, hey!
Super messed up on this one and did­n’t want to redo it

More Supports

To help fur­ther sta­bi­lize the struc­ture, I added side and roof sup­ports

Side Supports

  • Total of 4, using 1″ x 2″ wood, but only 3 for now

Roof Support

  • Dry fit, cut, glue, and screw (from bot­tom-up and top-down)

Camera Support

Camera Setup and Design

  • For the cam­era, I chose a sta­t­ic, solar-pow­ered one for this. Look­ing back, I kind of wish I’d cho­sen one that could be rotat­ed remote­ly, but this was cheap­er.
  • Find the mount­ing plate for the cam­era, and decide how it should be mount­ed on the struc­ture, tak­ing the cord attach­ment, length, and pow­er source into con­sid­er­a­tion
  • Set up the cam­era first, charg­ing it, con­fig­ur­ing it, and iron out any stor­age stuff
  • Dry fit every­thing, and deter­mine what is need­ed to secure it to the struc­ture
  • At this point, I lugged the unit out­side to ful­ly test the cam­era place­ment and make the deter­mi­na­tion for fur­ther mod­i­fi­ca­tions

Assembling the Camera Supports

  • Mis­take #3: Using small 2x4 blocks, and too large of screws
  • I want­ed the cam­era to set a lit­tle fur­ther back in a small, cov­ered alcove, if you will, so the width of a 2x4 was per­fect
  • Mea­sured, cut, drilled pilot holes, marked place­ment, then drove in screws…
  • …Only to find that the wood screws I bought were too big, the 2x4 too small and frag­ile:

So much for that

  • H’OKAY, THEN… just ply­wood it is
  • Mea­sure, cut, drill, screw part­way, place, screw ful­ly
  • Cut a tee­ny tiny bit of scrap to fill the lit­tle space between the roof and what juts out the back, then drill, and screw (glue, too, if desired)

Install Camera Mount

Note: In ret­ro­spect, I should have wait­ed until after the staining/sealing to do this because I end­ed up get­ting stain and seal­er all over the mount

  • Using either any pro­vid­ed tem­plates, or just a pen­cil, mark the holes
  • Choose appro­pri­ate screws and screw­driv­er
  • Dou­ble-check pic­ture on cam­era and hand access
  • Drill pilot holes, then screw in the mount

I men­tion “hand access” because you want to be able to remove, adjust, main­tain the cam­era, so if you can’t eas­i­ly loosen/tighten the mount attach­ment, then life just got more dif­fi­cult

Preliminary Clean-Up

  • Good time to tidy up equip­ment, mate­ri­als, and mess
  • Used the shop vac to clean off every­thing, includ­ing the unit
  • From here on out the only equip­ment need­ed will be sand­ing mate­ri­als, wood filler, sealant, and paint/stain stuff

Wood Filler

  • Using either a tack cloth or a damp tow­el, wipe any excess dust/wood par­ti­cles from the unit
  • Using a mix­ture of your hand and a put­ty knife, fill in holes and gaps with the wood filler. I start­ed with the put­ty knife but just end­ed up using my fin­gers. Gloves could be help­ful

Note: Wood filler can come in dif­fer­ent col­ors. If you’re choos­ing to use just a clearcoat seal­er, take this into con­sid­er­a­tion

  • Vac­u­um again. Wood filler is messier than I thought it would be

Sanding

My least favorite part of wood­work­ing

  • Wait until the wood filler is dry (read the instruc­tions, usu­al­ly 2 hours)
  • Sand the unit using a mix­ture of pow­ered ran­dom orbital sander and sand­pa­per for the hard­er to reach places
  • This will not only sand the rough areas smooth, but it will remove any pen­cil marks

Safe­ty first! Use eye and res­pi­ra­to­ry pro­tec­tion

Stain/Paint and Sealers

Safe­ty!! Seal­ers and stain are inhala­tion and spon­ta­neous fire haz­ards. Wear appro­pri­ate pro­tec­tion (eye, skin, res­pi­ra­to­ry), work in well-ven­ti­lat­ed areas (e.g. out­side), and have good dis­pos­al set­up ready (I always have a tray of water to sub­merge any stain-soaked equip­ment in)

Roof — Waterproof Sealer

  • I decid­ed to use Goril­la Brand Water­proof Patch + Seal because I’ve used it before on gal­va­nized met­al for an out­door dec­o­ra­tive item. It worked real­ly well and still with­stands sun and weath­er

Note: This prod­uct makes a mas­sive mess and smells ter­ri­ble. I rec­om­mend an apron, gloves, card­board bar­ri­ers, painter’s tape, pro­tec­tive work­space cov­er­ings, and work­ing out­side

  • With every­thing cov­ered well, and using a piece of card­board, spray away!
piece of card­board to catch over­spray

Before and After:

This is what hap­pens when you don’t use gloves. Since it’s water­proof, it was a night­mare to clean off. Wear gloves!!

  • I used an entire can on the first round, so I had to buy anoth­er one for the sec­ond round the next day. That means that it was able to cure overnight.
Wear­ing gloves this time

Stain + Spar Urethane

  • As the 2nd coat of roof seal­er was dry­ing, I decid­ed to just go ahead with the stain before the day heat­ed up (I was under­neath the deck, so there was shade)
  • I had the water tray set up to put every­thing the stain touched to pre­vent any spon­ta­neous fires (YES, they can cause fires, espe­cial­ly if you ball them up!!)
  • Gloves were real­ly nice not just for clean-up rea­sons, but to get stain where the paint­brush would­n’t reach well. You can also use a rag to apply the stain.
  • I did 2 coats (2‑hour dry in between with light sand­ing), and made sure to get 1 coat on the bot­tom of the unit, too
  • Remem­ber: Stain gets dark­er when ful­ly cured. I orig­i­nal­ly thought that the col­or was a bit light, then when I came to look the next day, it was as adver­tised on the can
Did­n’t end up using near­ly as much as I thought I would
Douse any­thing that has stain on it!!

Attach Camera

  • All that’s left to do now it to install the cam­era!
Just screws right in!

ALL DONE!!!

Notice the solar pan­el on the ground… Maybe I should secure it to a dif­fer­ent piece of wood?

Notes

  • You can put flow­ers on top. This was my orig­i­nal plan, but I need­ed to find a shal­low bowl pot to look bet­ter on top. This has not been done yet because the one I found is over $20 and I already spent enough on this darn thing
  • I used rub­ber shims to square up the feet
  • So far deliv­ery peo­ple have used it maybe 20% of the time which I find obnox­ious. Like­ly, it’s because they’d rather chuck my stuff up the stairs than actu­al­ly go up. The first per­son to use it was FedEx who put my stuff on top. *sigh* I think I might need to put up a sign? Did­n’t want to make it look more tacky

1 week later — Cracking

  • Went out and saw that after a week of super high heat and spon­ta­neous pow­er­ful storms, the roof seal­er was crack­ing and peel­ing!! It’s inter­est­ing to note that the shady side looks com­plete­ly fine, while the side that gets all the sun is crack­ing. Was it applied to heav­i­ly? Did it cure prop­er­ly? Def­i­nite­ly sun dam­age, though, because any video door­bell there will have its lens destroyed by sun with­in 1.5 years. I was super dis­ap­point­ed that it only made it 1 week.
  • In response, I quick­ly bought anoth­er Water­proof Patch & Seal, except this time it was a tape. This is the stuff that’s sup­posed to work under­wa­ter to seal off a leak.
  • Peel­ing off the pro­tec­tive plas­tic is a demon, but this will def­i­nite­ly not crack. I hope.
More peeled off as I was adding the new tape…
  • It does look a lit­tle janky, but what­ev­er. If I cared enough, I’d get anoth­er rub­ber­ized seal­er and cov­er this with that. Per­haps I’d try the paint-on kind this time instead of the spray which is so messy and glob­by. Will update if I end up doing that. I’m going to see how well this prod­uct works, first.

DIY: PVC and Hardware Cloth Garden Plant Enclosure + Winter Cover

writ­ten 8/5/2024, updat­ed 9/6/2025

Back to DIY Projects Page

Overview

What

Tem­po­rary/dis­as­sem­bly-pos­si­ble enclo­sure for patio and deck plants using PVC pipe and hard­ware cloth, fea­tur­ing doors

Why

Thiev­ing squir­rels, birds, and deer yet still allow­ing pol­li­na­tors, air, sun, and rain through

Time and Effort

Time: Sev­er­al hours to 1 day (maybe more)

Dif­fi­cul­ty: Mod­er­ate (depends on your equip­ment and mate­r­i­al sit­u­a­tion)

This is what start­ed it all. My beau­ti­ful can­taloupe brazen­ly stolen and eat­en right in front of my eyes by a crafty yet cute squir­rel

Materials and Cost

All mate­ri­als bought from Ama­zon and Home Depot

Mate­r­i­al

1″ 4ft PVC Pipe

1″ 6ft PVC Pipe

1″ x 1″ mesh 16-gauge 2′ x 50′ Hard­ware Cloth Roll

200′ 16-gauge Gal­va­nized Steel Wire

1″ PVC Hinges

1″ 90 Degree Elbow Fit­ting

1″ 3‑Way Fit­ting

1″ Tee Fit­ting

Cab­i­net Hard­ware Pulls

Quan­ti­ty

12 pipes

5 pipes

31ft

0.5 Roll

4 Hinges

8 Fit­tings

8 Fit­tings

2 Fit­tings

2 Pulls

TOTAL

Use Price

$80.40

$43.99

$24.80

$3.97

$36.68

$11.84

$26.00

$3.94

$4.38

$236.00

Owned Sup­plies:

Nee­dle Nose Pli­ers

Lines­man­’s Pli­ers

Diag­o­nal Cut­ting Pli­ers

Ratch­et­ing PVC Cut­ter

Sharpie

Mea­sur­ing Tape

Dig­i­tal Calipers

Rub­ber Mal­let

Bits/Driver

Screw Gauge

Planning and Schematics

Note: Draw­ings not to scale

Dimen­sions (L x W x H)

Out­er Dimen­sions: 45″ x 22″ x 53″

Door Dimen­sions: 20.5″ x 49″

Fit­ting Dimen­sions

3‑Way (For­mu­fit brand — 8 qty)

1¼ ” + 1⅜” = 2⅝” length

1.25in + 1.375in = 2.625in

90 Degree (Char­lotte Pipe brand — 8 qty)

1½” + 1⅛” = 2⅝”

1.5in + 1.125in = 2.625in

Tee (Char­lotte Pipe brand — 2 qty)

⅞” + 1⅜” + ⅞” = 3⅛”

0.875in + 1.375in + 0.875in = 3.125in

Pipe Lengths

Remem­ber that the ends of the pipes will fit into the fit­tings. All mea­sure­ments are approx­i­mate. Actu­al item dimen­sions may vary

Out­er Frame

42″ pipe (4 qty) — Length

19″ pipe (4 qty) — Width

50″ pipe (5 qty) — Height

Doors

17.5“pipe (4 qty) — Width

46.5″ pipe (4 qty) — Height

Over­all Weight

1 in, 4 ft PVC pipe = 1.4lbs

Over­all Weight of Enclo­sure: ~37lbs

Author’s Note

From start to fin­ish, con­cep­tion to assem­bly, this took a total of 3 days of time. Not count­ing wait­ing for parts, choos­ing parts, etc. The idea start­ed way back in 2022 when I was hav­ing issues with squir­rels steal­ing my toma­toes. I dreamed up and drew up plans, even going as far as to buy­ing much of the mate­ri­als to do it (orig­i­nal­ly out of wood and com­pos­ite wood). How­ev­er, the squir­rels quit steal­ing my stuff until this year when my veg­eta­bles and fruit dis­ap­peared one by one. The final straw was the baby can­taloupe! WARTIME. Since it would be placed on the deck instead of the ground like the orig­i­nal plans intend­ed, I need­ed a less weighty option and there­fore chose PVC pipe. Armed with the orig­i­nal plans, I altered them. You can plan all you’d like, but doing is com­plete­ly dif­fer­ent! So start­ed the 3 day-total-time jour­ney (real­ly, it took about a week wait­ing for all the pieces). Many, many cal­cu­la­tions, mis­cal­cu­la­tions, frus­tra­tions, and even blood shed­ding lat­er, I’ve — at this writ­ing — most­ly com­plet­ed the project. Just a few minor tweaks and a test run before final­iz­ing the hard­ware.

Over­ar­ch­ing Ques­tion: Does it actu­al­ly work???

As of August 2025: YES, IT WORKS suc­cess­ful­ly against thiev­ing squir­rels! They tried, hard with no suc­cess! (see Notes sec­tion for more)

Process

Gathering Supplies and Equipment

  • Buy hard­ware cloth that’s wide enough to not need so much over­lap. Like, one that can span from one side, to the back, and to the oth­er side. The top can be sep­a­rate.
  • If using the gal­va­nized steel wire method of attach­ment, then buy a Wire Twister Tool for Drill. Not only would that save tons of time, but phys­i­cal fatigue
  • Mea­sure the place­ment of the hinges before snap­ping them on
  • Paint it green or brown. White is so stark in the gar­den! Or if you have expend­able income, then buy For­mu­fit’s col­ored PVC
  • Fig­ure out a dif­fer­ent way to attach the hard­ware cloth (Ideas are all expen­sive yet remove­able: 2in Rub­ber Cable Clamps, 2 in Binder Rings, 6in Steel Wire Twist Bar­rel Key­chains, etc.)

Need­ed: Han­dles, PVC pipe, Ratch­et­ing pipe cut­ter, PVC fit­tings, hinges

Calculating, Measuring, Cutting, Assembling the Frame

Eas­i­ly the most time-con­sum­ing part. Using the spe­cial­ized PVC cut­ter and also a dig­i­tal caliper saved a lot of time. Just set­ting up the frame is easy. The hard part is fit­ting the doors prop­er­ly with­out cre­at­ing too much of a gap (try­ing to pre­vent crit­ter entry after all) around the door and frame while remem­ber­ing that the fit­tings add more length to each side (cal­cu­la­tions are done for you already in the schemat­ics above). On top of that, there’s the con­sid­er­a­tion of hard­ware cloth size to make as the hard­ware cloth is best wrap­ping around the pipe. If this was wood, it would be eas­i­er to just cre­ate a remov­able frame around the out­side of the cloth. Lots of re-mea­sur­ing and re-cut­ting until I got it right (or close enough).

Use a rub­ber mal­let to make sure the pieces are snug in the fit­tings

Hinges and Handles

This was more com­pli­cat­ed than it need­ed to be. Hard­ware includ­ed with the (unthread­ed) cheapo Han­dles are just too short to span the 1 in width of the PVC pipe. With­out buy­ing more or hav­ing to run out to a store, I delved into my giant box of ran­dom screws. Thank­ful­ly, I man­aged to find 4 that were both long enough and the right size (screw and thread gauges are use­ful). The Hinges snapped eas­i­ly onto the PVC and most­ly stay in place. And no won­der they stay in, because it gouges the plas­tic like no oth­er if you remove and slide them around, so make sure you’ve mea­sured where you want them first.

WARNING: Fas­ten any hinges before fas­ten­ing han­dles so that the han­dles are ori­ent­ed prop­er­ly, or at least mark loca­tions well. Because I wait­ed a year, my han­dles are now in a wonky ori­en­ta­tion

May 2025 — Hinge Per­ma­nence

Final­ly decid­ed to screw in the hinges. I was way too lazy to take the entire cab­i­net apart for the win­ter, but it end­ed up endur­ing the win­ter just fine

Used an 11⁄64″ bit, lined up the hinges on the pipe, and went for it. End­ed up using ran­dom screws that I hap­pened to have, so they’re all mis­matched and end­ed up rust­ing over the sum­mer

Attaching the Hardware Cloth

This is 16-gauge hard­ware cloth which is hard to find in stores (at least where I am). It’s big enough to allow pol­li­na­tors, water, and air into the enclo­sure, but small enough to thwart rodent and avian rob­bers. This was the lim­it­ing fac­tor for size of the enclo­sure as the cloth I used was only 2ft wide (they sell them larg­er). And no, chick­en wire is not rec­om­mend­ed. Not only are the holes too large, but the wire is weak. Also, to note, because this enclo­sure sits on the deck, there is no need for bot­tom cov­er­age. If I were to use the wood­en schemat­ics made to sit on the ground, then it would be ful­ly enclosed by wood, or extra cloth would need to be sunk into the ground (1–2 ft deep) to deter dig­gers.

The exceed­ing­ly time-con­sum­ing and phys­i­cal­ly painful part of this was the issue of how to attach hard­ware cloth to PVC. With­out spend­ing a for­tune, I decid­ed on a roll of gen­er­al-pur­pose gal­va­nized steel wire and some pli­ers. How­ev­er, giv­en how long it took to secure every­thing (5 hours! In the bak­ing sun and even through a short down­pour), I’ve been think­ing of a bet­ter attach­ment method (See NOTES sec­tion)

Twisty-ties from let­tuce are nice and long
Nav­i­gat­ing cor­ners
Cut to bend
Over­lap­ping pieces
Tem­po­rary twisty ties to hold two ver­ti­cal pieces of hard­ware cloth togeth­er
Bend­ing these under
3rd lay­er of over­lap (top, back, and side)
Twisting the Galvanized Steel Wire with Pliers

After much tri­al and error, I found that this was the fastest way (at least by hand) to tie off the 16-gauge steel wire (per­haps I should have used some­thing small­er)

Cut
Thread and ori­ent
Grab with line­man’s pli­ers
Twist
Keep twist­ing (be care­ful, though, twist­ing in the same spot too fast and hard will snap it)
Tight

Fun fact: If you feel the met­al after twist­ing, it’ll feel real­ly hot

Grab some nee­dle nose pli­ers and bend it away from pok­ing peo­ple
Safer!

Keep Going Until Completion

What’s annoy­ing is that tying off the hard­ware cloth with wire will cause ran­dom pock­ets where it bows out. Just keep on until every­thing is secure. Be aware that the ends of the hard­ware cloth and the steel wire are very sharp!

While the cam­era did­n’t focus on it, cut out pieces to make room for the han­dles
Trim­ming excess of doors
Trim­ming ends to pre­vent scratch­ing of feet or deck
Where doors meet. While does­n’t look ide­al, it works because touch­ing wire acts like a latch to hold them togeth­er
Hinges can still be manip­u­lat­ed since they’re not yet screwed in
Note the spac­ing between the hinge hard­ware. You can open or close the space just by twist­ing the hinge (hence why it has­n’t been secured until the end)

Complete!

Most­ly. No lock­ing hard­ware yet. Com­ing back to this 2 years after the fact, I’m still hold­ing strong with just a ball bungee through the 2 han­dles.

Wel­come home, can­taloupe plant!
3 total bungee cords to hold in place while in test­ing phase. Works real­ly well
Giv­en the space at the bot­tom where some­thing can push its way in, all I did was place a spare paver brick and voila!

Winter Cover

The aim was to have it decon­structable, but I was too lazy, so I decid­ed to use it as sort of a win­ter­ized green­hou­se­ish thing. My region is Zone 7B USDA har­di­ness. Two options (so far) for win­ter­i­za­tion.

Plastic Sheeting

Suit­able for mild win­ters with low dura­tion freez­ing peri­ods, about 20–40F.

Mate­r­i­al

6 mil Green­house Plas­tic Sheet­ing 12′ x 25′ (much too large)

Zip Ties

Pack­ing Tape (for cor­ners)

Pic­tures!

Plas­tic Sheet­ing. I bought entire­ly too much. Prob­a­bly need­ed half of that.
6 mil thick­ness
Zip tie secur­ing and tape for the cor­ners
Cut it off for neat appear­ance
Left open­ings around seams for ven­ti­la­tion and access
Poked a few drainage/vent holes in the top with a screw­driv­er

Plastic Sheeting Winterizing Results

2 months: hard freeze ear­ly Decem­ber for 1–2 weeks, and it’s dipped as low as the teens. So far so good. The plants seem to be doing just fine in there. I have hard neck gar­lic, straw­ber­ry, my blue­ber­ry plant, and onions.

Post-Win­ter: For about 5ish years, the win­ter had been pret­ty mild. 2024–2025 win­ter was nor­mal for this area which trans­lates to peri­ods of very cold and snow. Unfor­tu­nate­ly, that meant that my plas­tic lay­ers did NOT work well enough. If tem­per­a­tures stay around 20–40F, then the plas­tic is fine. If there are hard freezes for extend­ed peri­ods of time, this is not good enough. All of my plants died except the straw­ber­ry which did­n’t mind at all and looks amaz­ing (in a 10-gal­lon fab­ric pot). The blue­ber­ry most­ly died but final­ly start­ed sprout­ing new shoots from the root late June 2025. I was dis­ap­point­ed and will update again this fall when I set up the new ver­sion of this using hard plas­tic walls instead of the sheet­ing. Stay tuned!

Twin-Wall Polycarbonate Sheet

4′ x 2′ x 0.24″ Poly­car­bon­ate Green House Pan­els. They’re a rigid plas­tic sheet­ing that are shat­ter­proof which sup­pos­ed­ly allows them to with­stand severe weath­er, and keeps the green­house both warm in the win­ter and cool in the sum­mer. The work­ing tem­per­a­ture range is: ‑42°F to 248°F (-44°C to 120°C)

Stay-tuned! I will attempt to attach this to the struc­ture and report when I’m suc­cess­ful!

24″ x5

25.5″ x1

15″ x4

42″ x1

2 3‑way cor­ner, 1 straight exten­der, 4 tees

Notes

9/2025 — Added a snap-on door stop made with a 3D print­er to pre­vent the doors from swing­ing too hard inward. Easy to drill and per­ma­nent­ly attach to PVC pipe if desired. Through­out the grow­ing sea­son, had plants inside then enclo­sure that were able to be pol­li­nat­ed no prob­lem. Doors made it easy to access plants. End­ed up mov­ing the corn plants inside after squir­rel rob­bery. The enclo­sure was a tad too short for the corn, so tas­sels extend­ed out, but suc­cess­ful­ly thwart­ed squir­rels that tried hard to get into the corn (they oblit­er­at­ed the corn tas­sels try­ing to pull the entire plant out). Suc­cess!! Just bought the poly­car­bon­ate pan­els for a new attempt at cre­at­ing a cold frame for the win­ter. Still have yet to attach actu­al door latch­es and am still using a ball

Ball Bungee Cord is easy to use
Door stop that just snaps onto the PVC. Can be per­ma­nent­ly fas­tened. This is not at the moment

August 2024 — It’s been almost a month since test phase start­ed, and squir­rels have left it com­plete­ly alone. No evi­dence of rot­ting, so good air­flow, pol­li­na­tors busi­ly doing their thing, vines climb­ing the cloth like a trel­lis… alto­geth­er very hap­py with its func­tion. Even the bungee cords per­form well and are easy to remove. Still have not secured hinges or installed latch­es… and I’m not sure I want to. It would make for a refined prod­uct, but the bungee cords work well.

August 2025 — Squir­rels robbed me of corn, so moved the pot into the enclo­sure. SUCCESS!!! First true test against the rodents. They des­per­ate­ly want­ed the corn, but could not get in. They even tried to pull the corn up through the top by yank­ing on the tas­sels. All that did was rip the tas­sels off the plant. They nev­er got inside! Yay!! It WORKS!!!

If I were to do it again, I would do sev­er­al things:

Back to DIY Projects Page