Tag: measurements

Ford Mustang Mach‑E Dimensions

writ­ten 9/8/26, updat­ed 9/8/26

Yes, I know this isn’t a GT. It’s a Select AWD

Dimensions

Here, I have record­ed some dimen­sions for the Mach‑E for ref­er­ence. I’ve includ­ed exte­ri­or specs for all 3 mod­els, but inte­ri­or is for the GT/Rally

2020 — present (2026)

NOTE: The pic­tures have cov­ers and mats. The mea­sure­ments are for with­out them. Please be aware that mea­sure­ments are func­tion­al­ly approx­i­mate and not 100% exact

Exterior

Accord­ing to Ford’s Offi­cial Tech Specs

Mus­tang Mach‑E Select ER, AWDMus­tang Mach‑E GTMus­tang Mach‑E Ral­ly
Wheel­base117.5″117.5″117.5″
Length185.6″186.7″187.0″
Width74.1″74.1″74.1″
Height64″63.3″64.9″
Track Width, F63.5″63.5″63.5″
Track Width, R63.4″63.4″63.3″
Ground Clear­ance6.2″5.0″5.8″
Curb Weight4,748 lb4,993 lb5,016 lb

Con­ver­sion Sum­ma­ry — Aver­age and Approx­i­mate

Wheel­base: 9′ 9″

Length: 15′ 6″

Width: 6′

Height: 5′ 4″

Weight: 2.3 tons

Trunk Cargo Interior

Note: This is for the GT Ral­ly, so there’s less space inside than the Select and Pre­mi­um mod­els. I have car­go cov­ers and mats. Num­bers are cal­cu­lat­ed to be with­out the cov­ers and mats. All mea­sure­ments are approx­i­mate, not exact

Open­ing Width (Yel­low): 43″ down to 42″

Trunk Height (Orange): 25″ pil­lar; 28″ mid

Trunk Depth (Green): 30.75″ edge; 33″ mid

Open­ing Diag­o­nal (Pur­ple): 47″

Car­go Width (Pink): 42.5″ wheel bump; 46″ vents

Car­go Seats-down Length (Light Blue): 59″ to top of seats (not includ­ing head­rest)

Trunk Rim to Info­tain­ment Screen (White): 101″

Rear Seat Interior

Note: This is for the GT Ral­ly, so there’s less space inside than the Select and Pre­mi­um mod­els. The pic­tures show a dog seat cov­er. Mea­sure­ments are for with­out the cov­er, front seats at mod­er­ate posi­tion­ing, and all approx­i­mate.

Seat Length (Yel­low): 50″

Seat Height (Pur­ple): 25″ (to top of seat, exclud­ing head­rest)

Seat Depth (Orange): 19.25″

Height (Green): 36″ max (rear); 33″ min (thigh)

Car­go Length (Red): 52″ min (arm­rest); 57″ max (door)

Footwell (White): 10″ min (mod­er­ate posi­tion­ing)

2022 Ford Maverick Bed Measurements

2022 Ford Mav­er­ick XL Hybrid with Co-Pilot

I got the cheapo cheap­est pack­age (only added the Co-Pilot sys­tem). While it cer­tain­ly feels low cost, this gives me wig­gle room to upgrade!

Includ­ed are some mea­sure­ments I’ve tak­en of the FlexBed, pick­up bed, along with a clos­er look at the fac­to­ry screw holes.

Note: My bed nei­ther has a drop-in nor a spray-in lin­er.

Rear of Bed (near cab)

  • Green: rear wood plank divider slot
  • Blue: widest mea­sure­ment above the wheel wells
  • Yel­low: Indent on top of wheel wells
  • Pink: points to the direc­tion of truck cab, rear wall of bed

Tail­gate

  • Red: max­i­mum width open­ing of the tail­gate
  • Green: Height to top of tail­gate lip from the low­est part of bed floor (the con­cave, not con­vex por­tion of floor ridges)
  • Blue: denotes the tail­gate and both D‑pillars

Bed Side

  • Hot Pink: denotes truck cab, tail­gate, and bed floor
  • Beige: loca­tion and dis­tance between bed­side anchor screw holes
  • Medi­um Pur­ple: dis­tance between first set of bed­side screw holes
  • Orange: dis­tance between sec­ond set of bed­side screw holes
  • Yel­low: dis­tance between third set of bed­side screw holes
  • Light Blue: dis­tance between fourth set of bed­side screw holes
  • Green: length of bed­side screw hole chan­nel
  • Red: length of wheel arch shelf
  • Light Green: Space between rear of bed and rear wood divider
  • Medi­um Blue: approx­i­mate length of groove on top of wheel arch shelf
  • Dark Pur­ple: width of both wood div­er slots
  • Dark Blue: length of wheel arch shelf before it curves to the side of the bed
  • Gold: length of area between D‑Pillar and where the wheel arch starts to curve
  • Light pur­ple: dis­tance from top of bed to floor of bed

Flex Bed Notes

  • The length of the bed = the length of the ante­ri­or wood divider slot (43.5in or 110.49cm), mak­ing the Flex Bed an almost square flat wall to flat wall (see pic­tures at bot­tom of post)
  • The pre-drilled bed side holes are in unequal incre­ments
  • Bed side anchor point holes are all about 2 inch­es apart
  • The Bed­side screw hole chan­nel is use­ful for turn­ing and fit­ting the wood dividers for the flexbed
  • Floor tie down anchor point holes are dif­fer­ent from the bed side ones (scroll down to see more)
  • M6 x 1.0 are rec­om­mend­ed fas­ten­ers (Met­ric), with 1⁄4″ is most sim­i­lar in size (SAE)

Bed Side Anchor (near D‑Pillar)

  • The anchor holes (side and floor) are not thread­ed, so you’d either need self-tap­ping hard­ware or a tap­ping set.
  • Side anchor holes are M6 sized

Bed Floor Tie Down Anchor Point

  • Floor anchor holes are not thread­ed
  • They are larg­er than M6 screws, so are like­ly M8 sized
Hard to find anchors for this hole dis­tance
M6x1.0 is too small

Bed Side Screw Hole

  • Bed Side screw holes are thread­ed
  • M8 screws fit per­fect­ly inside
Thread­ed
M6x1.0 and 1⁄4″ are too small

But the M8x1.25 fits per­fect­ly!!

Pic­tures for Per­spec­tive

You can see the piece of wood which is the ante­ri­or wood divider. It fits per­fect­ly length­wise in the bed. The pos­te­ri­or divider is in place.